Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.     

Formation of toxic aldehydes in cod liver oil after ultraviolet irradiation

Formaldehyde, acrolein, malonaldehyde (MA), acetaldehyde and propanal produced from cod liver oil upon ultraviolet irradiation (λ_max=300 nm) were derivatized into nitrogenor sulfur-containing compounds and then analyzed by capillary gas chromatography with a nitrogen-phosphorus detector or a flame photometric detector. Acrolein and MA were formed at levels of 10.9±3.06 and 190.2±38.4 nmol/mg of fish oil, respectively. Maximum levels of formaldehyde, acetaldehyde and propanal formed were 7.0±0.90, 49.1±4.5 and 35.8±4.0 nmol/mg of oil, respectively. Formation of propanal in large quantities corresponded to the high content of ɛ-3 fatty acids in cod liver oil.     

Semiconductor photonic functional devices

Recent advances in semiconductor photonic functional devices based on the nonlinearities of laser diodes (LDs) are reviewed. Because the current research is driven primarily by the needs of optical fiber communications systems, most devices are made of InGaAsP and operate at wavelengths of between 1.3 and 1.55 μm, the wavelength window in which optical fibers have their most favorable properties. Minimum loss is at 1.55 μm, and zero dispersion is at 1.3 μm. AlGaAs devices operating at around 0.85 μm have also been reported. Two types of optical bistability-absorptive and dispersive-are explained, and devices based on them are described. Switching characteristics of bistable devices are discussed. Tunable wavelength converters and filters are also examined. Applications to all-optical communication and to optical switching systems are considered. Directions for future development are indicated     

Head-to-head polymers: 33. Bromination of cis-1,4-polybutadiene to head-to-head poly(vinyl bromide)

Cis-1,4-polybutadiene (PB) in a 0.5% solution of a solvent mixture of dichloromethane and 1,2-dibromoethane or tetrahydrofuran was quantitatively brominated with elemental bromine at 0°C under careful exclusion of oxygen to head-to-head poly(vinyl bromide). Partially brominated PB has a structure of random or block sequences of butadiene units in the polymer depending on the bromination solvent but shows no stereospecificity in the CHBrCHBr-dyads. Partially brominated PB with block structure showed a microphase-separated morphology over a wide range of composition. Microphase separation is less pronounced for the more random structure of butadiene units. I.r and ¹³C n.m.r. spectroscopy of the partially brominated PB was used to follow the progress of the bromination.     

Generation of adaptive gait patterns for quadruped robot with CPG network including motor dynamic model

This paper describes the generation of adaptive gait patterns using new Central Pattern Generators (CPGs) including motor dynamic models for a quadruped robot under various environments. The CPGs act as the flexible oscillators of the joints and adjust joint angles to required values. The CPGs are interconnected with each other and sets of their coupling parameters are adjusted by a genetic algorithm so that the quadruped robot can realize stable and adequate gait patterns. Generation of gait patterns results in the formation of the CPG networks suitable for the formation of not only a straight walking pattern but also of rotating gait patterns. Experimental results demonstrate that the proposed CPG networks are effective for the automatic adjustment of the adaptive gait patterns for the tested quadruped robot under various environments. Furthermore, the target tracking control based on image processing is achieved by combining the general gait patterns. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 35–43, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20225     

Taxonomy for protective ability of rust layer using its composition formed on weathering steel bridge

For a quantitative evaluation of the protectiveness of a rust layer formed on a weathering steel bridge, the relationship between the corrosion rate of the bridge and the composition of the rust layers formed on the girders was first investigated. These corrosion rates were clearly classified by the protective ability index (PAI) of α/γ^∗ and (β + s)/γ^∗, where α, γ^∗, β and s are the mass ratio of crystalline α-FeOOH, the total of γ-FeOOH, β-FeOOH and the spinel-type iron oxide (mainly Fe₃O₄), β-FeOOH and spinel-type iron oxide, analyzed by XRD, respectively. The inequality of the former index α/γ^∗ > 1 expressed the protectiveness criterion of the rust layer, while that of the latter index, (β + s)/γ^∗< 0.5 or > 0.5, classified the corrosion rate of the non-protective rust layer. The PAI is useful for a quantitative evaluation of the protectiveness of a rust layer formed on a weathering steel bridge and is an important item for the corrosion assessment of the bridge.     

Structural features of inclusion complexes of γ-cyclodextrin with various polymers

The crystalline structures of inclusion complexes of γ-cyclodextrin (γ-CD) with poly(ethylene glycol), poly(ethylene adipate), poly(propylene glycol) and poly(isobutylene) were studied by electron microscopy, in combination with X-ray diffraction works and measurements of thermal properties by DSC and TGA. The crystalline structure of as-prepared complexes was tetragonal and its cell dimensions were a = b = 2.380 nm and c = 1.48 nm. When an as-prepared sample was dried in a vacuum at room temperature, the tetragonal modification was transformed into the monoclinic one with the projected cell dimensions of a = 1.75, b = 1.36 nm and γ = 110°. The transformation occurred by progressive ‘shifting’ of rows of polymer necklaces in the [110] direction along the (110) plane in an original tetragonal lamellar crystal. Complexes lost weight by 10-15% in the process of heating up to 140 °C. The tetragonal crystalline modification was transformed into the hexagonal one, and concurrently, the X-ray diffraction profiles of annealed complexes were broadened. When a sample was dried in a vacuum at room temperature or annealed at high temperatures, followed by exposure to water vapor, the original tetragonal crystalline structure was recovered, restoring the original degree of orientation of crystallites in the sample. When water molecules were removed, the lateral stacking order of γ-CD-polymer complexes was destroyed, but the basic necklace structure in which polymer chains threaded through the cavity of γ-CD rings' structure could be retained.     

Preparation of water‐repellent silks by a reaction with octadecenylsuccinic anhydride

Silk fibers and membranes were acylated with octadecenylsuccinic anhydride (ODSA) at 75°C for different times. Swelling [N,N‐dimethylformamide (DMF) and dimethyl sulfoxide (DMSO)] and nonswelling (xylene) solvent media were used for the reaction. Silk membranes that reacted in DMF or DMSO displayed faster reaction kinetics and attained higher weight‐gain values than fibers. The effect of the solvent on the reaction yield was in the following order: DMSO > DMF ? xylene. The Fourier transform infrared spectra of acylated silk samples showed the characteristic absorption bands of the anhydride at 2990, 2852, 1780–1700, and 1170 cm^?1. The intensity of the latter band, which increased linearly with the weight gain, was used as a marker for evaluating the reaction kinetics of the samples acylated in the nonswelling medium. The moisture regain and water retention of silk fibers acylated with ODSA decreased significantly, regardless of the solvent system used. Accordingly, the water repellency increased. Acylation induced an increase in the thermal stability of the silk fibers and membranes. Fine particles adhering to the surfaces of the silk fibers acylated in xylene were detected by scanning electron microscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 324–332, 2003