Ideal amplifier spacing for reduction of Gordon-Haus jitter indispersion-managed soliton communications

Based on a variational analysis, the authors demonstrate that the noise-induced Gordon-Haus timing jitter in a dispersion-managed soliton transmission system can be substantially reduced by appropriate placement of the amplifiers     

The band areas of proteins determined by fluorescent scanning in the commercial automated gel electrophoresis apparatus

An automated gel electrophoresis apparatus, recently available commercially, allows one to follow the band during electrophoresis in real time, and lends itself therefore to an evaluation of bandwidth as a function of migration time (the dispersion coefficient), resolution and band shape. These determinations assume the constancy of band area with migration time and at various gel concentrations. The purpose of the present study was to verify these assumptions. Representative proteins and sodium dodecyl sulfate (SDS)-proteins, either natively fluorescent or fluorescein carboxylate labeled, were found to exhibit band areas which approach constancy as a function of migration time in both agarose and polyacrylamide gel electrophoresis, provided that (i) the protein concentration under the band was low enough to obviate self-quenching of fluorescence; (ii) the separation of the protein of interest from contaminants had progressed sufficiently during the time at which band areas were measured; (iii) the baseline under the peak was sufficiently well defined. However, band areas decrease with increasing gel concentration. Protein peaks exhibited leading and trailing tails. The ratio of the combined tail area to total area appeared to be near-constant at varying migration times. However, that ratio increases with increasing gel concentration. The tail area does not appear to be an artifact of fluorometric detection since it is reproduced upon fluorimetric analysis of the protein eluted from gel slices after electrophoresis. However, it may be due to photochemical destruction under the conditions of repetitive fluorometric peak detection.     

Measurements of single chain form factors by small-angle neutron scattering from polystyrene blends containing high concentrations of labelled molecules

A series of small angle neutron scattering measurements on blends of normal polystyrene (PSH) and labelled (deuterated) polystyrene (PSD) have been made with concentrations of PSD from 5 to 50 mol %. It is shown that the single chain form factor of the polymer in bulk can be obtained from a single concentration measurement for any concentration of labelled molecules, providing the molecular weights of the parent and labelled molecules are the same and the molecular weight distributions are narrow.     

Quantitative prediction of the degree of pollution of effluent from reactive dye mixtures

By using mathematical formulae developed in previous studies, certain pollution parameters of dye effluent obtained from reactive dyeing with a single dye can be predicted with good accuracy. In this study, the degree of pollution of reactive dyeing effluent using dye mixtures was also predicted by other approaches, such as linear and non-linear regression. The prediction accuracy was found to be satisfactory.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

The binding of substrates and inhibitors to the metal center of myoinositol monophosphatase

The synthetic substrate anthraniloyl-beta-glycerol-P binds to myoinositol monophosphatase with a Kd = 5 microM at pH 7.5. The anthraniloyl chromophore, excited at 330 nm, sensitizes the long lived luminescence of bound Tb(III) at 490, 545, 585 and 620 nm. Assuming a mechanism of radiationless energy transfer, the actual distance of separation between the donor-acceptor pair was calculated to be R = 10 A. Tb(III) binds to the monophosphatase with a Kd = 2 microM, whereas Ca-(II) displaces the lanthanide at concentrations above 0.1 mM. The binding studies support the notion that Tb(III), Ca(II) and Mg(II) interact with a common binding site on the protein. Phosphate ion, a strong competitive inhibitor, perturbs the luminescence of bound Tb(III), whereas the substrate beta-glycero-P has no effect on the luminescence yield and long-lived emission of bound Tb(III). It is suggested that the phosphate group of the substrate is not in direct contact with the metal ion coordinated to several amino acid residues of the enzyme.     

Gordon-Haus timing jitter reduction in dispersion-managed solitoncommunications

An analytic theory is presented which demonstrates that the noise induced Gordon-Haus timing jitter in arbitrary dispersion-managed transmission systems is reduced by the power-enhancement factor required to support a dispersion-managed solitons provided the path-average soliton period is much greater than the dispersion-map period. The analysis further predicts the behaviour of the amplitude, width, and quadratic chirp fluctuations due to the amplified spontaneous emission (ASE) noise     

Development of the bi-directional ultrasound system for base of tongue imaging

The use of conventional ultrasound systems to image the upper airway has been limited because ultrasound energy is attenuated by the air column. In an attempt to study upper airway geometry, we developed a computer controlled bi-directional ultrasound system which combines two conventional ultrasound devices with computer image processing to yield images of upper airway structures. Human studies and cadaver studies were performed to evaluate the system. Images acquired by the bi-directional ultrasound system were comparable to images from 3D volume rendered CT scans. This system may provide valuable data in the study of upper airway physiology and pathology.     

A systematic design method to obtain broadband characteristics for singly-fed electromagnetically coupled patch antennas for circular polarization

We present a systematic, empirical design technique to obtain optimum broadband impedance, axial-ratio (AR) and gain bandwidths for a singly-fed electromagnetically coupled patch antenna for circular polarization. Our investigation has also revealed tradeoffs amongst obtainable AR, impedance bandwidth and AR bandwidth. Using two design examples at different frequency bands and for different senses of circular polarization, we have demonstrated the effectiveness of the proposed knowledge-based tuning method. We have obtained at C-band measured values of impedance bandwidth (VSWR/spl les/2) equal to 43%, 3-dB AR bandwidth of 8%, AR of less than 0.3 dB and a mean gain level of 7 dB. For the Ku-band element, a 40% impedance bandwidth and a 17.3% of 3-dB AR bandwidth have been obtained with a peak gain of 7.2 dBic.