DC and AC characteristics of sub-50-nm MOSFETs with source/drain-to-gate nonoverlapped structure

A MOSFET structure with a nonoverlapped source/drain (S/D) to gate region was proposed to overcome the challenges in sub-50-nm CMOS devices. Key device characteristics were investigated by extensive simulation study. Fringing gate electric field through the spacer induces an inversion layer in the nonoverlap region to act as an extended S/D region. An oxide spacer is used to reduce parasitic gate overlap capacitance. A reasonable amount of inversion electrons were induced under the spacers. Internal physics, speed characteristics, short channel effects, and RF characteristics were studied with the nonoverlap distance at a fixed metallurgical channel length of 40 nm. The proposed structure had good drain-induced barrier lowering and V/sub T/ rolloff characteristics and showed reasonable intrinsic gate delay and cutoff frequency compared to those of an overlapped structure.     

Study of polymer‐network structure on polymer‐stabilized blue phase

Abstract— To understand the mechanism of the disclination defect of the liquid‐crystal (LC) phase, this study was conducted to directly analyze the polymer‐network (PN) structure of polymer‐stabilized blue phase (PSBP), which is minutely formed on all LC layers. The PN was examined after first removing the glass decap and then the LC. Important to note is that the removal of the glass decap did not affect or damage the PN structure. The PN was determined to be a stable structure without any change to the thickness of the layer. When removing the LC, both hexane and acetone solutions were used. Moreover, there was no structural deformation to the PN when using the hexane solution. The results of the study show that the actual size of the polymer chain is in fact 50–60 nm, five times larger than previous theories which estimated the size to be only 10 nm. In addition, this study confirmed that the pores between the PN are 100–200 nm. The PN structure was shown to be susceptible to change based on different heating temperatures. In summation, now that defect lines of a LC display (LCD) could be directly measured, further progress and development in the theoretical interpretations of the Kerr effect on PSBP can be realized.     

Frictional properties of VA‐mode alignment‐film surfaces studied by frictional force microscopy

Abstract— The surface‐friction characteristics of the post‐bake temperature were compared to that of the rubbing condition on VA‐mode alignment films (AFs) using frictional force microscopy (FFM). The surface roughness and the surface frictional force increased when the temperature was elevated. However, the frictional asymmetry could not be detected by the frictional loop due to the instability of the side‐chain molecular arrangement. For the inter‐influences of the total friction and surface roughness, the density of the side chain was changed and it was intentionally rubbed for evaluation. The results showed that the total friction was higher when the rubbing was stronger and side‐chain density lower, and the surface roughness also increased in the same manner. This can be explained by the potential interaction due to the curved structure of the side‐chain surface that establishes the probe that is scanned and the top surface layer. In order to confirm the influence of the pre‐tilt angle on the tilt of the side chain, a test cell was produced under the same conditions and evaluated. The results showed that the pre‐tilt‐angle decreased according to the difference in density of the side chain and strength of rubbing after injecting liquid‐crystal (LC).     

Modification of Solidification Structure Under DC Pulse Magnetic Field

A new process using direct cunent pulsed magnetic field for modification of solidification structure of pure aluminium has been investigated.The experimental results show that the fine equiaxed crystal zone exists at the bottom of ingots with pulse magnetic,and with the increase of rated output current the equiaxed grains are more finer.     

Geckoprinting: assembly of microelectronic devices on unconventional surfaces by transfer printing with isolated gecko setal arrays

Developing electronics in unconventional forms provides opportunities to expand the use of electronics in diverse applications including bio-integrated or implanted electronics. One of the key challenges lies in integrating semiconductor microdevices onto unconventional substrates without glue, high pressure or temperature that may cause damage to microdevices, substrates or interfaces. This paper describes a solution based on natural gecko setal arrays that switch adhesion mechanically on and off, enabling pick and place manipulation of thin microscale semiconductor materials onto diverse surfaces including plants and insects whose surfaces are usually rough and irregular. A demonstration of functional ‘geckoprinted’ microelectronic devices provides a proof of concept of our results in practical applications.     

Effects of the Surface Contact on the Uncertainty in Indentation Yield Strength: Surface Roughness and Angular Misalignment

Metals and Materials International - We suggest a method for accurately estimating the uncertainty of indentation yield strength determined from the modified Meyer relation as a mathematical...     

Sliding-induced adhesion of stiff polymer microfibre arrays. I. Macroscale behaviour.

Gecko-inspired microfibre arrays with 42 million polypropylene fibres cm(-2) (each fibre with elastic modulus 1 GPa, length 20 microm and diameter 0.6 microm) were fabricated and tested under pure shear loading conditions, after removing a preload of less than 0.1 N cm(-2). After sliding to engage fibres, 2 cm2 patches developed up to 4N of shear force with an estimated contact region of 0.44 cm2. The control unfibrillated surface had no measurable shear force. For comparison, a natural setal patch tested under the same conditions on smooth glass showed approximately seven times greater shear per unit estimated contact region. Similar to gecko fibre arrays, the synthetic patch maintains contact and increases shear force with sliding. The high shear force observed (approx. 210 nN per fibre) suggests that fibres are in side contact, providing a larger true contact area than would be obtained by tip contact. Shear force increased over the course of repeated tests for synthetic patches, suggesting deformation of fibres into more favourable conformations.     

Synthesis of diketopyrrolopyrrole (DPP)-based small molecule donors containing thiophene or furan for photovoltaic applications

Two π-conjugated small molecules based on diketopyrrolopyrrole (DPP), DPP4T and DPP2F2T, were synthesized using the Suzuki coupling reaction. DPP4T and DPP2F2T contained furan and thiophene, respectively, next to a DPP core. Organic photovoltaic cells (OPVs) were fabricated using two DPP-based oligothiophenes as donors. DPP4T showed higher power conversion efficiency (PCE) (1.44%) than DPP2F2T (0.85%). The short-circuit current (J_SC) of DPP4T (4.38 mA cm⁻²) was nearly twice that of DPP2F2T (2.49 mA cm⁻²). The improved photovoltaic properties of DPP4T could be explained by the optical properties and the film morphology.     

Highly Efficient Video Codec for Entertainment‐Quality

We present a novel video codec for supporting entertainment‐quality video. It has new coding tools such as an intra prediction with offset, integer sine transform, and enhanced block‐based adaptive loop filter. These tools are used adaptively in the processing of intra prediction, transform, and loop filtering. In our experiments, the proposed codec achieved an average reduction of 13.35% in BD‐rate relative to H.264/AVC for 720p sequences.