A cathode readout gas sampling calorimeter with conductive plastic tubes

We constructed and tested a prototype gas sampling electromagnetic calorimeter of the Pb-proportional tube sandwich type. The calorimeter uses conductive plastic tubes and cathode pad readout with a tower structure which resulted in reasonable energy and spatial resolutions for electrons in the momentum range 0.5–4.0 GeV/c; $\text{σ}{}_{\mathrm{E}}\text{E =}\text{21\%}\text{(E(}\text{GeV}\text{)}\text{)}{}^{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}\text{, σ}{}_{\mathrm{x}}\text{= 6}\text{mm}\text{(at 3 GeV}$/c). This paper describes the test and the performance studied under various conditions.     

Carbon Nanotubes Grown on the Surface of Cathode Deposit by Arc Discharge

Carbon nanotubes prepared by de arc discharge of graphite electrodes in He and CH₄ gas took markedly different morphology. Thick nanotubes embellished with many carbon nanoparticles were obtained by evaporation under high CH₄ gas pressure and high arc current. Thin and long carbon nanotubes were obtained under a CH₄ gas pressure of 50Torr and an arc current of 20A for the anode with a diameter of 6mm.     

Use of a YAP1 overexpression cassette conferring specific resistance to cerulenin and cycloheximide as an efficient selectable marker in the yeast Saccharomyces cerevisiae.

Drug-resistance markers for yeast transformation are useful because they can be applied to strains without auxotrophic mutations. However, they are susceptible to technical difficulties, namely lower transformation efficiency and the appearance of drug-resistant mutants without the marker. To avoid these problems, we have constructed a phosphoglycerate kinase (PGK) promoter-driven YAP1 expression cassette, called PGKp-YAP1. Yeast cells containing PGKp-YAP1 were resistant to cycloheximide, a protein synthesis inhibitor, and also to cerulenin, a fatty acid synthesis inhibitor, but not to other drugs tested. The transformation efficiency of PGKp-YAP1 using cerulenin selection was comparable to that using a URA3 auxotrophic marker when low concentrations of cerulenin were used. Non-transformed drug-resistant colonies did appear on the low-concentration cerulenin plates. However, these non-transformed colonies could easily be identified, based on their cycloheximide sensitivity and/or their resistance to aureobasidin A to which the transformants were sensitive. Therefore, the dual drug resistance of PGKp-YAP1 could be used as an effective selection for PGKp-YAP1 recipient cells. The PGKp-YAP1 marker was used to disrupt the LYS2 gene and to transform an industrial yeast strain, indicating that this marker can be used for efficient and reliable gene manipulations in any Saccharomyces cerevisiae strain.     

MITI projects on recycling

MITI has actively done R&D on industrial technology for waste and reclamation and so there are many research items from small scale to large scale. However, Ecofactory and researches on recycling of metallic materials are introduced here. Ecofactory was proposed by the Mechanical Engineering Laboratory and is now at the stage of the Leading Research, a new research scheme in AISt. Researches on recycling of metallic materials are being done with subsidy. Those researches should contribute to both the preservatin of the global environment and effective recycling of waste materials.Abbreviations AIST Agency of Industrial Science and Technology - MITI Ministry of International Trade and Industry - NEDO New Energy and Industrial Technology Development Organization     

R & D Needs - Drying of Ceramics

New research and development needs for the drying of ceramics are prooosed. The researches on the ceramic drying are briefly reviewed and the role of the drying in the ceramic production process iS summarized. The drying must deal with molded materials and the problem is of significant difference from another drying with particulate materials. It means that the drying must be performed with keeping the molded feature and the insufficient completion of drying and the careless operation influence directly on the product quality The importnance of the R & D on the heat and moisture transfer. shrinking mechanism. the deformation behavior and the strain-stress formation in the molded clay issuggested. The subjects are also pointed out for the further improvement of the ceramic drying process and the precise design of molding with high quality.     

EXPANSION AND STRESS RELAXATION OF EXPRESSED CAKE

Expansion and stress relaxation of expressed cake are discussed.

The expansion process of expressed cake after release of load is very similar to consolidation of solidndashliquid mixtures, although a liquid flow in the expansion process is opposite in direction to that in consolidalion. This process can be analyzed well by use of the Terzaghi Voigt combined model. It is shown that the rate of primary deformation in expansion is much smaller than that in consolidation under the same change in compressive pressure. It is also found that the ratio of secondary deformation to total deformation in expansion is much larger than that in consolidation.

Stress relaxation of expressed cake, which is observed when expression is stopped before attaining an equilibrium compression state of a material, can be explained by use of a consolidation and expansion theory. In the relaxation process, local expansion appears near the drainage surface while local consolndash idation appears near the center of the cake. The equilibrium cake stress is uniquely determined by the average consolidation ratio when the expression is interrupted.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

An Electronic Approach to Materials Design

A molecular orbital approach to materials design has recently made great progress. This approach is based on the electronic structure calculations by the DV-Xα cluster method. In this paper recent progress in this approachis reviewed. In particular     

Drying-Induced Strain and Stress: A Review

This paper is to review the works on strains and suesses in materials during drying.The strains and suesses are caused when temperature and moisture gradients are generated in mterials whose volume changes with heating and moisture removal. In such materials. failure and irregular deformion may be generated which affect considerably the qudity of the products after drying. In the first part. modeling procedure is introduced for the analysis of the strain-stress behavior in elaslic. viscous and visccelastic materials combined with heat and moisture transfer. An overview of the works on swains and stresses and drying characteristics are presented for malerials such as porous media. clay. sol-gels. agricultural products and foods in the second part. There are some materials that show both elasticity of the solid phase and viscosity of the fluid phase ( water or solvena∥ or viscoelasticiry. The suesses are often correlated with a suction pressure of fluids in pores and the flow rate is based on Dacy's equation for the elastic and viscous tnedia and a kind of viscoelastic media. The general canstitulive equalions. for suains and svesses are often analyzed with the stain behavior given by a function of moisturr for some media ai well. The emohasis is on the inuoduclion of comprehensive criteria for undersunding the problems of strain and stress development in materials subjected to drying.     

Immunohistochemical study of epithelioid hemangioendothelioma in the leg: a case report

Epithelioid hemangioendothelioma is a relatively rare lesion. Although its histogenesis has been well described, its immunohistochemical characteristics remain controversial. A case of epithelioid hemangioendothelioma of the soft tissue of the right leg in a 67-year-old Chinese woman is reported. Histologic findings of intracytoplasmic lumina in the tumor cells and positive immunostaining for vimentin, factor VIII-related antigen. CD34 and Ulex europaeus agglutinin 1 (UEA-1) were obtained, demonstrating differentiation of the tumor cells to endothelial cells, although staining for antibodies to cytokeratins AE1/AE3 and CAM5.2 was weak. CD34 as well as Factor VIII-related antigen is a useful marker of endothelial differentiation in this tumor. A review of the literature is also presented.