A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

Efficiency of repeated batch penicillin fermentation using two fermentors. Computer simulation and optimisation

Repeated batch operation using two fermentors (RBTF) to penicillin fermentation was demonstrated by computer simulation to improve productivity. Three operation modes were compared: chemostat, repeated batch operation using a single fermentor (RBSF) and RBTF; in each case account was made of the lag period before growth. The simulated fermentor performances were assessed on the basis of the penicillin productivity and concentration; the simulation was based on published batch fermentation data. It was shown that RBTF was superior to RBSF and chemostat. The advantage of RBTF increased as the lag period became greater.     

Annual changes in serum vitellogenin concentrations in viviparous eelpout, Zoarces elongatus

Vitellogenin of matrotrophic viviparous eelpout (Zoarces elongatus) was purified from estradiol-17 beta (E2) treated immature male sera by gel chromatography and anion exchange chromatography. Isolated vitellogenin has a molecular weight of 540 kDa estimated by gel chromatography. Serum levels of vitellogenin in females were measured during oocyte development and gestation by single radial immunodiffusion. Serum vitellogenin level was low (less than 0.2 mg/ml) during the early vitellogenic period, increased in the late vitellogenic period to a peak level (6.4 +/- 2.1 mg/ml) at the beginning of gestation. After that it rapidly decreased to a low level (0.1 +/- 0.1 mg/ml) during the early gestation period. Levels of vitellogenin remained low throughout the gestation period. Serum E2 levels in females showed increased from 1.3 to 3.0 ng/ml during the late vitellogenic period, and declined to 0.4 ng/ml during the early gestation period. Serum levels of E2 showed good correlation with serum vitellogenin levels, suggesting that the vitellogenin synthesis is controlled by E2 in this species. These results combined with the matrotrophic growth of embryo during gestation suggest that there is a shift in the synthesis of maternal nutritional products for embryos from the yolk to other nutrients.     

Is it possible to differentiate between choledochal cyst and congenital biliary atresia (type I cyst) by antenatal ultrasonography?

Both choledochal cyst and congenital biliary atresia (type I cyst) may share the same ultrasonographic pattern. We report 2 cases which were shown to have cystic structures on the upper abdomen by antenatal ultrasonography. The size of the choledochal cyst found at 24 weeks' gestation increased steadily as gestational age advanced. But the size of the cyst in congenital biliary atresia found at 29 weeks' gestation remained unchanged throughout the remaining pregnancy. Cyst enlargement, therefore, may suggest the possibility of a choledochal cyst.     

Advanced Coatings on Furnace Wall Tubes

Nickel-based self-fluxing alloy coating extends the service life of furnace wall tubes at waste incineration plants due to its excellent corrosion resistance and heat resistance. Fusing of such coatings by induction heating offers improved efficiency and reliability of products. Compared with conventional plasma, flame, and high-velocity oxy-fuel spraying thermal-sprayed coatings, induction-fused coatings provide a far stronger metallurgical bond at the interface, while minimizing the inclusion of pores. In addition, the tubes are less costly than those with welded coatings, and the process reduces the distortion of the products, facilitating easier final assembly. A successful experimental application of 11 units in a waste incinerator revealed virtually no corrosion on the exposed surfaces, and showed an improved water heating efficiency over that of the original tubes. Such units are now being employed in four incinerators in Taiwan, and continuing tests are showing great promise.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

Microstructure Control of Thermally Sprayed Co-Based Self-Fluxing Alloy Coatings by Diffusion Treatment

This article describes microstructure control aimed for wear-resistance improvement of Co-based (Co-Cr-W-B-Si) self-fluxing alloy coating by diffusion treatment. The diffusion treatments of thermally sprayed Co-based self-fluxing alloy coating on steel substrate were carried out at 1370-1450 K for 600-6000 s under an Ar gas atmosphere. Microstructural variations of the coating and the interface between the substrate and the coating were investigated in detail. A proper diffusion treatment precipitates two kinds of fine compounds in Co-based matrix. X-ray diffractometer (XRD) and electron probe microanalyzer (EPMA) analysis revealed these precipitates to be a chromium boride dissolving cobalt and a tungsten boride containing cobalt and chromium. The size of each precipitate became larger with increasing treatment temperature and time. A coating with the proper size borides showed a superior wear-resistance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Grain refinement and superplasticity in a magnesium alloy processed by equal-channel angular pressing

The extrusion/equal channel angular pressing (EX-ECAP) processing procedure, in which magnesium-based alloys are subjected to extrusion followed by ECAP, was applied to a Mg-7.5 pct Al-0.2 pct Zr alloy prepared by casting. Microstructural inspection showed the EX-ECAP process was effective in reducing the grain size from ∼21 μm after extrusion to an as-pressed grain size of ∼0.8 μm. It is shown through static annealing that these ultrafine grains are reasonably stable up to 473 K, but grain growth occurs at higher temperatures. Tensile specimens were cut from the billets prepared by EX-ECAP and testing showed these specimens exhibited superplasticity at relatively low temperatures with maximum elongations up to >700 pct. By processing through EX-ECAP to a higher imposed strain and thereby increasing the area fraction of high-angle boundaries, it is demonstrated that there is a potential for achieving high-strain-rate superplasticity. This article is based on a presentation made at the Symposium entitled “Phase Transformations and Deformation in Magnesium Alloys,” which occurred during the Spring TMS meeting, March 14–18, 2004, in Charlotte, NC, under the auspices of the ASM-MSCTS Phase Transformations Committee.     

Achieving enhanced ductility in a dilute magnesium alloy through severe plastic deformation

Experiments were conducted to evaluate the utility of a new processing procedure developed for Mg-based alloys in which samples are subjected to a two-step processing route of extrusion followed by equal-channel angular pressing (designated as EX-ECAP). The experiments were conducted using a Mg-0.6 wt pct Zr alloy and, for comparison purposes, samples of pure Mg. It is shown that the potential for successfully using ECAP increases in both materials when adopting the EX-ECAP procedure. For the Mg-Zr alloy, the use of EX-ECAP produces a grain size of ∼1.4 μm when the pressing is undertaken at 573 K. By contrast, using EX-ECAP with pure Mg at 573 K produces a grain size of ∼26 μm. Tensile testing of the Mg-Zr alloy at 523 and 573 K after processing by EX-ECAP revealed the occurrence of significantly enhanced ductilities with maximum elongations of ∼300 to 400 pct.     

Bone Tissue Engineering in Rat Calvarial Defects Using Induced Bone-like Tissue by rhBMPs from Immature Muscular Tissues In Vitro

This study aimed to induce bone-like tissue from immature muscular tissue (IMT) in vitro using commercially available recombinant human bone morphogenetic protein (rhBMP)-2, rhBMP-4, and rhBMP-7, and then implanting this tissue into a calvarial defect in rats to assess healing. IMTs were extracted from 20-day-old Sprague-Dawley (SD) fetal rats, placed on expanded polytetrafluoroethylene (ePTFE) with 10 ng/μL each of rhBMP-2, BMP-4, and BMP-7, and cultured for two weeks. The specimens were implanted into calvarial defects in 3-week-old SD rats for up to three weeks. Relatively strong radiopacity was observed on micro-CT two weeks after culture, and bone-like tissue, comprising osteoblastic cells and osteoids, was partially observed by H&E staining. Calcium, phosphorus, and oxygen were detected in the extracellular matrix using an electron probe micro analyzer, and X-ray diffraction patterns and Fourier transform infrared spectroscopy spectra of the specimen were found to have typical apatite crystal peaks and spectra, respectively. Furthermore, partial strong radiopacity and ossification were confirmed one week after implantation, and a dominant novel bone was observed after two weeks in the defect site. Thus, rhBMP-2, BMP-4, and BMP-7 differentiated IMT into bone-like tissue in vitro, and this induced bone-like tissue has ossification potential and promotes the healing of calvarial defects. Our results suggest that IMT is an effective tissue source for bone tissue engineering.