A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Generation of adaptive gait patterns for quadruped robot with CPG network including motor dynamic model

This paper describes the generation of adaptive gait patterns using new Central Pattern Generators (CPGs) including motor dynamic models for a quadruped robot under various environments. The CPGs act as the flexible oscillators of the joints and adjust joint angles to required values. The CPGs are interconnected with each other and sets of their coupling parameters are adjusted by a genetic algorithm so that the quadruped robot can realize stable and adequate gait patterns. Generation of gait patterns results in the formation of the CPG networks suitable for the formation of not only a straight walking pattern but also of rotating gait patterns. Experimental results demonstrate that the proposed CPG networks are effective for the automatic adjustment of the adaptive gait patterns for the tested quadruped robot under various environments. Furthermore, the target tracking control based on image processing is achieved by combining the general gait patterns. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 35–43, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20225     

FDTD analysis of switching characteristics in magnetooptic functional devices using magnetostatic surface waves

Collinear magnetooptic interaction with magnetostatic surface waves (MSSW) can be used for wavelength‐selective switches, wavelength filters, and frequency shifters in wavelength‐division‐multiplexed (WDM) photonic networks and optical processing systems. The switching efficiency can be improved with a multilayer waveguide structure. To investigate the dynamic switching characteristics, the FDTD method was employed. The mode conversion between TE and TM mode was successfully demonstrated with FDTD simulation. The filtering characteristics were also evaluated. The FDTD results were compared with the result from the coupled mode theory, and good agreement was obtained. Switching of an optical pulse was also demonstrated by the FDTD method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(1): 40–47, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20501     

Subcellular localization of Bcl-2 protein in synovial sarcoma

The subcellular localization of Bcl-2 protein in surgically resected, fixed-frozen tissue specimens of seven tumors from six cases of synovial sarcoma and a synovial sarcoma cell line was examined using laser-scanning confocal microscopy and immunoelectron microscopy. Bcl-2 protein in synovial sarcoma cells was detected in the nuclear envelope, endoplasmic reticulum membrane, and mitochondrial circumference. Based on the finding of pre-embedding immunoelectron-microscopy observation, the distribution of Bcl-2 protein in such membranous organella was patchy. A computer-based image analysis failed to reveal any quantitative differences between the inner and the outer mitochondrial membranes. The tumorigenesis of synovial sarcoma is also discussed from the viewpoint of Bcl-2 overexpression.     

Dynamic moduli for short fiber-CR composites

The dynamic moduli, E′ and E″, and tan δ for nylon–CR and PET–CR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed two dispersion peaks for nylon–CR composite. The peak at ?28°C corresponded to the main dispersion of CR and the peak at 100°C to the α-dispersion of nylon 6. For a PET-CR composite, in addition to the individual dispersion of CR and PET, a small and broad peak was observed at about 90°C. The angular dependence of E′ indicated that the short fibers assumed good orientation. The storage modulus for the composites was given by the parallel model as E′ = V_f′E_f + V_mE′_m., where E′_c, E′_f and E′_m were the storage modulus for the composite, fiber, and matrix and V_f and V_m were the volume fraction of fiber and matrix, respectively. In the transverse direction of fiber, the peak values of tan δ at ?28°C were given by the following equation; tan δ_c = tan δ_m ? δV_f, where tan δ_c and tan δ_m are the loss tangent for the composite and matrix, respectively, and α is coefficient depending on fiber type. The results indicated that a region with strong interaction was formed between fibers and CR matrix.     

Prediction model of compressive strength development of fly-ash concrete

Based on experimental results concerning the compressive strength development of concrete containing fly ash, the authors derived an estimation equation for compressive strength development. The equation can express coefficient , which indicates the activity of fly ash as a binder, in the form of a function of age, fly-ash content, and Blaine specific surface area of fly ash.

This equation is capable of explaining the increases in the early strength due to fly ash in place of part of fine aggregate, the decreases in the early strength due to fly ash in place of part of cement, the increases in the long-term strength due to pozzolanic reaction, the relationship between the fly-ash replacement ratio and the ratio of strength increase/decrease, and the effect of fly ash's Blaine specific surface area on the strength.     

Electrochemical formation of AlN in molten LiCl-KCl-Li3N systems

Electrochemical formation of aluminum nitride was investigated in molten LiCl-KCl-Li₃N systems at 723 K. When Al was anodically polarized at 1.0 V (versus Li⁺/Li), oxidation of nitride ions proceeded to form adsorbed nitrogen atoms, which reacted with the surface to form AlN film. The obtained nitrided film had a thickness of sub-micron order. The obtained nitrided layer consisted of two regions; the outer layer involving AlN and aluminum oxynitride and the inner layer involving metallic Al and AlN. When Al electrode was anodically polarized at 2.0 V, anodic dissolution of Al electrode occurred to give aluminum ions, which reacted with nitride ions in the melt to produce AlN particles (1-5 μm of diameter) of wurtzite structure.