Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Superconductivity in W-containing diamond-like nanocomposite films

Superconductivity in a tungsten-containing carbon-oxide film was reported. The film with 500 nm thickness was deposited onto polycrystalline silicon oxides using chemical vapor deposition and the co-sputtering of a tungsten metal target. The bonding state of the carbon atoms and the macroscopic and microscopic crystal structure of the film were investigated by Raman spectroscopy, X-ray diffraction and transmission electron microscopy measurements. From the experimental results, we determined that this film essentially had an amorphous structure. The temperature dependence on resistivity was measured in the temperature range of 2–300 K. Resistive superconducting transition was observed at 3.8 K. The dc magnetizations were measured in the temperature range of 1.8–6.5 K. The diamagnetism resulting from a superconductive state was observed below 3.75 K, which is consistent with a resistive superconducting transition. It is thought that the finite sized clusters of the different superconductive transition temperatures cooperatively produce a macroscopic superconducting phenomenon.     

Drawing plane graphs nicely

Summary This paper presents two efficient algorithms for drawing plane graphs nicely. Both draw all edges of a graph as straight line segments without crossing lines. The first draws a plane graph convex if possible, that is, in a way that every inner face and the complement of the outer face are convex polygons. The second, using the first, produces a pleasing drawing of a given plane graph that satisfies the following property as far as possible: the complements of 3-connected components, together with inner faces and the complement of the outer face, are convex polygons. The running time and storage space of both algorithms are linear in the number of vertices of the graph.     

Simple chemical syntheses of TAG monohydroperoxides

For the purpose of synthesizing standards to be used in the quantification of TAG hydroperoxides, three TAG (1,2-dioleoyl-3-palmitoylglycerol, 1-oleoyl-2-linoleoyl-3-palmitoylglycerol, and triolein) monohydroperoxides were chemically synthesized as authentic specimens. TAG were prepared by using a simple condensation in pyridine of glycerol and the corresponding acid chlorides. These TAG were then converted into monohydroperoxides by a photosensitized peroxidation. The synthesized monohydroperoxides were analyzed by normal-phase and RP-HPLC. The results of normal-phase HPLC analysis showed that monohydroperoxides from a corresponding TAG were a mixture of regioisomers. In RP-HPLC, however, the regioisomers of monohydroperoxides were not separated and gave a single peak, which may improve the sensitivity for the detection of TAG monohydroperoxides. In this study TAG monohydroperoxide standards were synthesized; these will be useful for the study of yet unknown biological and pathological roles of TAG hydroperoxides.     

Photocatalysts using hexa- and octa-titanates with different tunnel space for water decomposition

Photocatalytic activities for water decomposition were examined for photocatalysts using hexa- and octa-titanates and TiO2(B) with different tunnel space in the structure. Using RuO2 as promoter, M2Ti6O13 (M = Li, Na, K, Rb) showed the stoichiometric production of Hz and O₂ except for Li, whereas H₂Ti₈O₁₇ and TiO₂(B) had very low activity producing only hydrogen as a product. The effects of promoters on Na₂Ti₆O₁₃ showed that the activity increased in the order of RuO₂ > RuO₂ + IrO₂ > IrO₂ > RuO₂ + Pt > MnO₂. These effects along with other related ones are discussed: it emerges that the presence of the tunnels is important for the achievement of high photocatalytic activity.     

Glass transition behavior of emulsion-polymerized polymer films containing a surface-active agent

The glass transition behavior of emulsion-polymerized poly(methyl methacrylate) and polystyrene films containing sodium laurylsulfate as emulsifier was studied by measurements of dynamic mechanical properties and thermal depolarization current. The film specimens of the emulsion-polymerized polymers were prepared by casting from their benzene solutions. The glass transition temperatures of the emulsion-polymerized films are higher than those of the bulk-polymerized films. The higher glass transition temperature of the emulsion-polymerized films is attributed to the colloidal properties of sodium laurylsulfate in the process of the film formation. The restriction of the molecular chains in the emulsion-polymerized films is attributed to the interaction between the hydrophobic groups of sodium laurylsulfate and the polymer molecules.