PES News

This paper presents a new method for the generation of a reference voltage for a dynamic voltage restorer (DVR). These voltages, when injected in series with a distribution feeder by a voltage source inverter, can tightly regulate the voltage at the load terminal against imbalance or harmonics in the source side. It is stipulated that the DVR does not supply any real power in the steady state. The reference voltage generation scheme is validated through digital computer simulation studies.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

High yield formation of carbon nanotubes using a rotating cathode in open air

Carbon nanotubes (CNTs) have been synthesized using the arc discharge method with a rotating graphite disc as the cathode. Arcing was carried out in open air and without the use of catalysts. The current density was maintained constant through out the experiment, while, the rate of rotation of the cathode and atmosphere under which arcing was carried out were changed during experimentation. Characterization of the samples produced indicates that rotation of the cathode has a significant impact on the quality and yield of the process. It is proposed that rotation of the cathode drags plasma formed between two electrodes away from high temperature region. This results in a sudden quenching of the reactive plasma. The time available for nucleation and growth phenomena is significantly reduced and thus leads to the formation of highly graphitic multi walled CNTs (yield 60%) and traces of double walled CNTs.     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.     

Propagation of a quasi-shear horizontal acoustic wave in Z-Xlithium niobate plates [and conductivity sensor application]

It is found that an acoustic wave which is nearly polarized in the shear horizontal (SH) direction can propagate along the X axis of a Z-cut lithium niobate plate if the ratio h/λ, where h=plate thickness and λ=acoustic wavelength, is less than about 0.5. Attractive properties of this quasi-SH wave include: (1) phase velocity nearly constant for all values of h/λ; (2) ability to propagate in contact with a liquid medium; and (3) electromechanical coupling coefficient as high as 0.15. These properties make the wave attractive for use in a variety of sensor and signal processing applications. An example of sensor applications is illustrated by using the wave to measure conductivity of liquids (aqueous KCl solution). The frequency of a 12-MHz quasi-SH mode oscillator fabricated on a 0.48 wavelength thick Z-X lithium niobate plate is found to vary by more than 80 kHz for variation in KCI concentration from 0 to 0.15%     

Performance evaluation of a teletext system

Four parameters are defined to measure the performance of a teletext system, namely, the probability of delivering a message within specified time, the transmission efficiency, the average number of errors per page, and the throughput. Each of them is derived and computational results are presented taking the UK teletext system as an example. These parameters are compared in their ability to characterize the performance of the teletext system     

Rectilinear steiner tree heuristics and minimum spanning tree algorithms using geographic nearest neighbors

We study the application of the geographic nearest neighbor approach to two problems. The first problem is the construction of an approximately minimum length rectilinear Steiner tree for a set ofn points in the plane. For this problem, we introduce a variation of a subgraph of sizeO(n) used by YaO [31] for constructing minimum spanning trees. Using this subgraph, we improve the running times of the heuristics discussed by Bern [6] fromO(n ² log n) toO(n log² n). The second problem is the construction of a rectilinear minimum spanning tree for a set ofn noncrossing line segments in the plane. We present an optimalO(n logn) algorithm for this problem. The rectilinear minimum spanning tree for a set of points can thus be computed optimally without using the Voronoi diagram. This algorithm can also be extended to obtain a rectilinear minimum spanning tree for a set of nonintersecting simple polygons.The results in this paper are a part of Y. C. Yee's Ph.D. thesis done at SUNY at Albany. He was supported in part by NSF Grants IRI-8703430 and CCR-8805782. S. S. Ravi was supported in part by NSF Grants DCI-86-03318 and CCR-89-05296.