Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

Diffusion coefficient in polymer solutions

Molecular diffusivity of a solute in a solvent may be determined by measuring the extent of dispersion of solute in solvent flowing in a straight circular tube under the conditions of laminar flow. This simple and rapid method for determination of molecular diffusivity in aquous polymer solutions is discussed. Experimental results show a substantial reduction in the solute diffusivity with increase in polymer concentration.     

Flow regimes,hold–up and pressure drop for two phase flowin helical coils

Experimental results on flow pattern, hold–up and pressure drop are presented for cocurrent upward and downward air water flow in helical coils. A tube of 0.01 m internal diameter was used and the ratio of coil to tube diameter was varied from 11 to 156.5. Water flow rate was varied from 4.9 × 10-⁶ m³/s to 92 × 10-⁶ m³/s while the range of gas flow rate covered was 83 × 10-⁶ m³/s to 610 × 10-⁶ m³/s. A new mechanistic approach is proposed to correlate pressure drop data in coils. The proposed model retains the identity of each phase and separately accounts for the effects of curvature and tube inclination resulting from the torsion of the tube. This makes it possible to use a single model to predict pressure drop for both upward and downward two–phase flow in coiled tubes. Required correlations for hold–up, interfacial friction factor and friction factors for individual phases are provided.     

Gas-liquid mass transfer in three-phase fluidized beds with viscous pseudoplastic liquids

Liquid phase volumetric mass transfer coefficients for oxygen were determined in three-phase fluidized beds of 8 mm glass spheres fluidized by a cocurrent flow of air and pseudoplastic polysaccharide solutions (carboxymethyl cellulose, xanthan). A semi-theoretical relation for the effective shear rate was suggested. The mass transfer coefficients could be correlated, together with literature data for particle diameters of 3 mm and 5 mm in other liquids, using the terminal velocity as the particle-specific property.     

Modal analysis of human body vibration model for Indian subjects under sitting posture

Need and importance of modelling in human body vibration research studies are well established. The study of biodynamic responses of human beings can be classified into experimental and analytical methods. In the past few decades, plenty of mathematical models have been developed based on the diverse field measurements to describe the biodynamic responses of human beings. In this paper, a complete study on lumped parameter model derived from 50th percentile anthropometric data for a seated 54- kg Indian male subject without backrest support under free un-damped conditions has been carried out considering human body segments to be of ellipsoidal shape. Conventional lumped parameter modelling considers the human body as several rigid masses interconnected by springs and dampers. In this study, concept of mass of interconnecting springs has been incorporated and eigenvalues thus obtained are found to be closer to the values reported in the literature. Results obtained clearly establish decoupling of vertical and fore-and-aft oscillations.     

DeepKnuckle: revealing the human identity

Multimedia Tools and Applications - Identification and authentication are ubiquitous questions which pan across various systems. In certain domains, they are of paramount importance. Like, security...     

Software fault prediction using Nonlinear Autoregressive with eXogenous Inputs (NARX) network

This paper explores a new approach for predicting software faults by means of NARX neural network. Also, a careful analysis has been carried out to determine the applicability of NARX network in software reliability. The validation of the proposed approach has been performed using two real software failure data sets. Comparison has been made with some existing parametric software reliability models as well as some neural network (Elman net and TDNN) based SRGM. The results computed shows that the proposed approach outperformed the other existing parametric and neural network based software reliability models with a reasonably good predictive accuracy.     

Numerical simulations of drop impact and spreading on horizontal and inclined surfaces

The phenomenon of drop spreading is important to several process engineering applications. In the present work, numerical simulations of the dynamics of drop impact and spreading on horizontal and inclined surfaces were carried out using the volume of fluid (VOF) method. For the horizontal surfaces, the dynamics of impact and spreading of glycerin drops on wax and glass surfaces was investigated for which the experimental measurements were available [Šikalo, Š., Tropea, C., Ganic, E.N., 2005a. Dynamic wetting angle of a spreading droplet. Experimental Thermal and Fluid Science 29, 795-802; Šikalo, Š., Tropea, C., Ganic, E.N., 2005b. Impact of droplets onto inclined surfaces. Journal of Colloid and Interface Science 286, 661-669]. The influence of surface wetting characteristics was investigated by using static contact angle (SCA) and dynamic contact angle (DCA) models. The dynamics of drop impact and spreading on inclined surfaces and the different regimes of drop impact and spreading process were also investigated. In particular, the effects of surface inclination, surface wetting characteristics, liquid properties and impact velocity on the dynamics of drop impact and spreading were investigated numerically and the results were verified experimentally. It was found that the SCA model can predict the drop impact and spreading behavior in quantitative agreement with the experiments for less wettable surfaces (SCA>90^°). However, for more wettable surfaces (SCA<90^°), the DCA observed at initial contact times were order of magnitude higher than SCA values and therefore the DCA model is needed for the accurate prediction of the spreading behavior.     

Removal of dyes from a synthetic textile dye effluent by biosorption on apple pomace and wheat straw

This paper deals with two low-cost, locally available, renewable biosorbents; apple pomace and wheat straw for textile dye removal. Experiments at total dye concentrations of 10, 20, 30, 40, 50, 100, 150, and 200 mg/l were carried out with a synthetic effluent consisting of an equal mixture of five textile dyes. The effect of initial dye concentration, biosorbent particle size, quantity of biosorbent, effective adsorbance, dye removal and the applicability of the Langmuir and Freundlich isotherms were examined. One gram apple pomace was found to be a better biosorbent, removing 81% of dyes from the synthetic effluent at a particle size of 2 mm x 4 mm and 91% at 600 microm. Adsorption of dyes by apple pomace occurred at a faster rate in comparison to wheat straw. Both the isotherms were found to be applicable in the case of dye adsorption using apple pomace.     

Conduction studies on Ta2O5 layer under different metallic electrodes

Rectification studies on Ta₂O₅ anodic oxide layers with vacuum-deposited Au, Ag, Pb, Bi, Sb contacts have been made. No correlation between critical voltage and work function for metal electrodes was found. Non-uniform and unpredictable behaviour of Ta₂O₅ films under different metals have indicated the dominant dependence of conduction on the flaw density in the oxide film.