Anthocyanin composition of the red wine Babić affected by maceration treatment

Identification of anthocyanins in the wine made of the Croatian autochthonous grape variety of Babić (Vitis vinifera L.) was carried out and their profile was determined by means of high-performance liquid chromatography with diode array and mass spectrometric detection. Dependence of anthocyanins content and profile on maceration treatment conditions was investigated. Statistically significant differences of anthocyanins concentration in wines Babić produced by various maceration treatments were confirmed by the use of multivariate analysis of variances. The investigation results indicated that the maceration temperature exerts higher influence on anthocyanins concentration than the duration of maceration. In addition, on the basis of anthocyanin composition and using different multivariate statistical analyses, differentiation of wines Babić according to maceration treatments was procured.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

An approach to efficient business intelligent system for financial prediction

A concept of business intelligent system for financial prediction is considered in this paper. It provides data needed for fast, precise and good business decision support to all levels of management. The aim of the project is the development of a new online analytical processing oriented on case-based reasoning (CBR) where a previous experience for every new problem is taken into account. Methodological aspects have been tested in practice as a part of the management information system development project of “Novi Sad Fair”. A case study of an improved application of CBR in prediction of future payments is discussed in the paper. This paper is originally presented at The International Conference on Hybrid Information Technology 2006, at the special session on “Intelligent Information Systems for Financial Engineering”, November 2006 in Cheju Island, Korea.     

Changes in polymer foils used in food packaging tested by using differential scanning calorimetry

This work is an experimental study of the differential scanning calorimetry characterisation of polymer materials used in food packaging materials, such as polypropylene (0.03 mm), polyethylene (0.1 and 0.03 mm), poly(D-(-)-Β-hydroxybutyrate) (powder), two-layered polypropylene (0.064 mm), and two-layered polypropylene with poly-vinylidene-chloride (0.012/0.021). The polymer stability was checked by simulation of conditions during food preparation in microwave ovens, sterilisation or rapid freezing. The materials were tested in the temperature range from 40 to 200‡C at different scan rates from 2 to 30°C min⁻¹ during heating or cooling. The enthalpies show a high correlation coefficient (0.964) with scan rate. All samples undergo phase change in the temperature range from 107 to 173°C during heating and enthalpies are in the range from 31.8 to 71.1Jg⁻¹. Upon subsequent cooling from 200°C, the temperature range of phase changes is shifted to lower temperatures from 86 to 102°C with enthalpies ranging from 30.4 to 57.8 J g⁻¹. Experiments with exposure of polymers to microwave radiation and freezing prove that the phase change considering the temperature range is very similar in all experiments.     

Low temperature and strain rate dependence of fracture stress and fracture toughness on thin Fe40Ni40B20 amorphous ribbon

The fracture stress and the critical stress intensity factor of the Fe₄₀Ni₄₀B₂₀ amorphous metallic ribbons 20 μm thick were measured in the temperature range 4.2–300 K and at deformation rates from 3.3×10⁻⁶ to 1.25×10⁻³ m⁻¹ with the aim to obtain more information on the condition for the onset and development of the inhomogeneous plastic deformation and fracture.     

Vortices in anisotropic type-II superconductors

We present a generalized variational model of an isolated vortex, valid in the anisotropic case when the external magnetic field is along one of the symmetry directions. We discuss the effects of the field anisotropy on the core and magnetic pinning of individual vortices.     

How to Control Robots Interacting with Dynamic Environment

The goal of this paper is to shed light on the control problem of constrained robot motion from the aspect of the dynamical nature of the environment with which the robot is in contact. Therefore, the criticism of traditional hybrid control which allows position/force feedback loops to split into independent control with respect to position and force, is not the main point we want to make. Reference to the papers written by the founders of hybrid control and their numerous followers served only to better understand the reason and motivation for suggesting a different approach to control of robots interacting with environment.The paper has a predominantly review character, based on recently published work. It also contains some new, unpublished results in the framework of the unified approach to the position/force control of robots, proposed by the present author and his co-workers. By pointing to the possibility of introducing an environment dynamics in the contact tasks of the machining type, the author emphasizes that the proposed dynamically interactive control can be applied to a completely different class of tasks, in which a contact is made between the system (constructions or structure) and very specific kinds of dynamic environments.