溶剂浸渍树脂的萃取分离性能研究

介绍了溶剂浸渍树脂的制备及性能,阐述了溶剂浸渍树脂在产物提纯和废水处理等分离过程中的应用,并对使用溶剂浸渍树脂处理含酚废水进行了初步研究.     

1270轧机弹性曲线的回归及参数估计

首先介绍了轧机弹性曲线的基础知识及 1 2 70轧机AGC系统的基本结构 ,然后论述了数据采集的方法 ,最后根据最小二乘法得到轧机弹性曲线的回归模型及刚度系数的实验结果。     

浅析局域网的安全技术

随着计算机网络的不断发展和广泛运用,局域网的安全问题也越来越受到人们的关注。本文将阐述局域网的存在的一些不安全因素及相应的安全策略和采用的安全技术。     

轧辊轴承位的电刷镀修复

轧辊轴承位的修复有多种方式，传统的堆焊修复技术是将轧辊完全拆卸后进行堆焊，然后热处理，在车床上进行精加工到规定尺寸精度。堆焊修复技术的缺点是堆焊后轴头需机加工，修复成本高，时间长。对于轧辊轴承位磨损尺寸较小的轧辊，我厂采用电刷镀修复技术对轧辊轴承位进行修复，降低了成本，节省了时间，收到了较好的修复效果。     

基体碳对C/CF/Cu复合材料的影响

采用树脂碳化和碳气相沉积相结合的方法制备了碳/碳纤维(C/CF)先驱丝,用压力浸渗凝固成型方法制备了碳/碳纤维/铜(C/CF/Cu)复合材料,借助于扫描电镜下复合材料界面和相分布观察以及显微硬度和滑动摩擦磨损测试,探讨了基体碳(树脂碳化碳和沉积碳)对C/CF/Cu复合材料成型、显微硬度及摩擦磨损的影响.结果表明,碳化和碳气相沉积处理的C/CF先驱丝相对致密并阻碍铜液的压力浸渗成型,但该先驱丝硬度高于碳化处理的C/CF先驱丝.碳化和碳气相沉积处理的C/CF/Cu复合材料滑动摩擦磨损耐磨性高于纯铜,而且滑动摩擦系数也高于纯铜.C/CF/Cu复合材料是一种具有摩阻功能的复合材料.     

胺对镍系催化了二烯聚合规律的影响

以二乙胺为例研究了胺对Ｎｉ（ｎａｐｈ）２－Ａｌ（－Ｂｕ）３－ＢＦ３·ＯＥｔ２＋ｎ—Ｃ８Ｈ１７ＯＨ（简称Ｎｉ－Ａｌ－Ｂ＋ＲＯＨ）和Ｎｉ（ｎａｐｈ）２－Ａｌ（ｉ－Ｂｕ）３－ＢＦ３·ＯＥｔ２＋ＣＨ３ＣＯＯＣ４Ｈ９（简称Ｎｉ—Ａｌ—Ｂ＋ＢＡ）两体系聚合活性和聚合物分子量的影响，并与Ｎｉ—Ａｌ—Ｂ体系进行了对比．考察了通常条件下肢的允许含量，讨论了有胺存在时Ｎｉ／Ｂｄ、Ａｌ／Ｎｉ、Ａｌ／Ｂ摩尔比的变化对聚合规律的影响。结果表明：胺的含量高于２０ｐｐｍ时将使聚合活性和分子量降低，提高催化剂用量可以抑制胺的不利影响。     

Enhanced utilization bound of Rate-Monotonic scheduling in Controller Area Networks

When priorities to message streams are assigned using Rate Monotonic (RM) for a Controller Area Network (CAN), the utilization bound is known to be about 25% for CAN 2.0A and 29% for CAN 2.0B. In this letter, we present a higher utilization bound than the existing ones with a reasonable constraint. The new utilization bounds are approximately 34% for CAN 2.0A and 41% for CAN 2.0B if no single message stream's utilization exceeds 46% or 27% of the total utilization for CAN 2.0A or CAN 2.0B, respectively.     

3—乙酰基—5—溴 酚酮的合成

2-乙酰基-7-甲氨基酮1与溴反应得2-乙酰基-7-甲氨基-4-溴酮2。2与氢氧化钠反应得3-乙酰基-5-溴酚酮3。化合物2和3是两种新化合物,其结构已经红外光谱、核磁共振谱及元素分析证实。     

Electrical behavior of carbon black-filled polymer composites: Effect of interaction between filler and matrix

The effect of interaction between carbon black and polymer on electrical behavior was studied using the ESR method. The polymer matrices used were HDPE, LDPE, and ethylene/vinyl acetate (EVA). Two kinds of carbon blacks (CB), high structure CSF-III and low structure FEF, were used as a conductive filler. Compared to that of the HDPE/FEF compound, the positive temperature coefficient (PTC) intensity is lower and electrical reproducibility is worse for the HDPE/CSF-III compound; however, it can be improved significantly by radiation cross-linking. On the other hand, the cross-linking has no practical effect on the PTC intensity of the LDPE/CSF-III compound while it can be achieved by mixing the compound for a longer time. The great PTC intensity was obtained in the HDPE/EVA/CSF-III compound, and it is greater than that of HDPE/CSF-III or EVA/CSF-III. We explain these results using the concept of interaction between the filler and matrix. The absorption of the polymer on the carbon black surface may be physical or chemical; the latter is caused by the free-radical reaction between the polymer and carbon black, and it can occur during the radiation or preparation process of the compound. These “bound polymers” are essentially important for materials to have a great PTC intensity and good reproducibility. © 1994 John Wiley & Sons, Inc.