Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

A cathode readout gas sampling calorimeter with conductive plastic tubes

We constructed and tested a prototype gas sampling electromagnetic calorimeter of the Pb-proportional tube sandwich type. The calorimeter uses conductive plastic tubes and cathode pad readout with a tower structure which resulted in reasonable energy and spatial resolutions for electrons in the momentum range 0.5–4.0 GeV/c; $\text{σ}{}_{\mathrm{E}}\text{E =}\text{21\%}\text{(E(}\text{GeV}\text{)}\text{)}{}^{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}\text{, σ}{}_{\mathrm{x}}\text{= 6}\text{mm}\text{(at 3 GeV}$/c). This paper describes the test and the performance studied under various conditions.     

An equation of state for 1,1-difluroethane (HFC 152a)

An equation of state for 1,1-difluoroethane (HFC 152a, CH₃CHF₂) has been developed on the basis of reliable experimental data including PVT, liquid C_p, and saturated-liquid-density data measured by our group. It is a non-dimensionalized virial equation whose functional form is the same as that originally developed for 1,1,1,2-tetrafluoroethane (HFC 134a) in our group. The effective range is for pressures up to 15 MPa, temperatures from 230 to 450 K, and densities to 1000 kg m⁻³. The equation represents reliable PVT measurements within ± 1% in pressure for the superheated vapour and supercritical fluid, while within ±0.5% in density for the compressed liquid. In addition, it should be noted that the equation represents the other essential thermodynamic properties including vapour pressures, saturated-liquid/ vapour densities, isobaric/isochoric specific heats and sound velocity in both the liquid and gaseous phase of HFC 152a.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Removal of endocrine disrupting chemicals (EDCs) using low pressure reverse osmosis membrane (LPROM).

Endocrine disrupting chemicals (EDCs) are the focus of current environmental issues, as they can cause adverse health effects to animals and human, subsequent to endocrine function. The objective of this study was to remove a specific compound of EDCs (i.e. pentachlorophenol, C(6)OCL(5)Na, molecular weight of 288 g/mol) using low pressure reverse osmosis membrane (LPROM). A cross flow module of LPROM was used to observe the effects of operating parameters, i.e. pH, operating pressure and temperature. The design of the experiment was based on MINITAB(TM) software, and the analysis of results was conducted by factorial analysis. It was found that the rejection of pentachlorophenol was higher than 80% at a recovery rate of 60 to 70%. The rejection was subjected to increase with the increase of pH. The flux was observed to be increased with the increase of operating pressure and temperature. This study also investigated the interaction effects between operating parameters involved.     

Silica removal from Mokai, New Zealand, geothermal brine by treatment with lime and a cationic precipitant

Preliminary experiments using two chemicals (CaO, a quicklime, and a cationic nitrogen-bearing precipitant, EC-004) to remove silica from geothermal brine were undertaken at the Mokai geothermal plant, New Zealand. The brine was mixed with the reagent (CaO or EC-004). The reaction was studied from the start of the experiment (NRT, 0 min, no retaining time) and after 15 min (15RT) at 90 °C. The concentration of silica in the brine was initially 954 mg/l, and decreased linearly with increasing reagent concentration. When CaO is added, the silica concentration at 15RT was 200 mg/l lower than at NRT and became almost zero on addition of 1.5 g/l. In contrast, when EC-004 is added, the total silica concentration nearly reaches the solubility of amorphous silica at 90 °C. In order to prevent silica scaling in Mokai brines cooled to 90 °C, the CaO and EC-004 added should be individually adjusted to 0.5 g/l and 80 mg/l, respectively.     

Structure and dynamics of suspensions of silica particles in liquidcrystals under a low frequency AC applied voltage

Silica particles dispersed in liquid crystals exhibit a novel behavior such as a unique migrating behavior and alignment. These characteristics are found to depend on the size of the nanoparticles, the surface state of nanoparticles, the liquid crystal (LC) phases, the amplitude and the frequency of applied voltage. These are discussed in terms of anisotropic particle-particle and particle-LC molecules interactions in the anisotropic environment of liquid crystal matrix     

Surface Hardening of Carbon Steel Using High Powered YAG Laser

A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate.     

Far-Infrared Reflection Spectra of Dielectric Ceramics for Microwave Applications

Far-infrared reflection spectra of dielectric ceramics, BaSm₂Ti₅O₁₄, BaTi₄O₉, and some pcrovskites such as Ba(Zn_1/3Nb_2/3)O₃, have been measured at room temperature using a Fourier transform infrared spectrometer in order to investigate the effect of the crystal structure on the dielectric properties. As for perovskites, Sr(Zn_1/3Nb_2/3)O₃ and Sr(Mg_1/3Nb_2/3)O₃, in which B site ions are ordered, were also measured. Reflectance data were analyzed by means of a factorized form of dielectric functions instead of the classical dispersion theory, and all of the spectra were well fitted. The values of dielectric constants and tan δ calculated from the reflectance data were in good agreement with resonant cavity measurements at 5 GHz. Furthermore, results of this study have shown that the main contribution to the microwave dielectric properties is caused by low-frequency optically active modes located at 50 to about 300 cm⁻¹, and for perovskite structures it is suggested that the ordering of B site ions is significant in obtaining low dielectric losses.