Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Optical-transmission characteristics of optical-fiber cables and installed optical-fiber cable networks for WDM systems

Many cables containing 1.3-/spl mu/m zero-dispersion single-mode (SM) optical fibers are installed in trunk and access networks. Recently, there have been a number of studies on wavelength-division-multiplexing (WDM) systems designed to increase transmission capacity and flexibility. If we can construct WDM systems using SM optical-fiber cable networks designed to transmit using wavelengths in the 1.3-/spl mu/m window (O-band), this will prove very effective in reducing construction costs. It is therefore important to examine the wavelength dependence of the transmission characteristics of SM optical-fiber cables and networks that have already been installed and in which several optical fibers are joined. In this paper, we describe the measured optical characteristics of SM optical-fiber cables and installed optical-fiber cable networks at various wavelengths. The optical characteristics were stable in the 1.46 to 1.625-/spl mu/m wavelength range and we confirmed that the installed SM optical-fiber cable networks could be used for WDM system applications.     

Reducing cycle times in manufacturing and supply chains by input and service rate smoothing

A key performance parameter of a manufacturing network or supply chain is its cycle time; the time that a typical item spends in the network. A previous simulation study on a semiconductor assembly and test facility showed that cycle times could be reduced by having smooth input and service rates. This suggested that there is a “cycle time principle” that, for a system with a specified throughput or input rate, the shortest cycle times are obtained when the input and service rates do not vary over time. We prove that this principle is true for the M/G/1 and M/M/s queueing systems and Jackson networks. The analysis involves establishing several results on the concavity of waiting time probabilities and the convexity of expected waiting times and queue lengths, as functions of input and service rates. These results also have natural uses in other optimization problems.     

The effect of copper on the crystallization of hexagonal boron nitride

The crystallization process of hexagonal boron nitride in the presence of copper has been investigated. The positive effect of copper on the crystallinity of boron nitride was observed in the three studied systems of: nitrided boron, nitrided boron–carbon, and previously prepared turbostratic boron nitride. However, the presence of copper hindered the formation of boron carbonitride and produced graphite and boron nitride phases separately. Poor crystallinity was found as a conditio sine qua non for the existence of such a compound. Well-crystallized boron nitride had a very low spacing parameter 0.3328 nm and a regular hexagonal shape.     

Neural mechanism of pupillary dilation elicited by electro-acupuncture stimulation in anesthetized rats

The neural mechanisms to reflex dilation elicited by electro-acupuncture stimulation were investigated in anesthetized rats. Two needles, with 160 microns diameter and about 5 mm apart, were inserted into the skin and underlying muscle of a hindpaw. Repetitive 20 Hz, 0.5 ms electrical pulses at various intensities were used for stimulation for 30s. The pupil size was magnified about 44 times via a microscope and was continuously recorded on a videotape. Electro-acupuncture stimulation at more than 0.5 up to 6 mA induced stimulus intensity-dependent pupil dilation. These responses were abolished by the severance of the sciatic and saphenous nerve of the stimulated hindlimb. Compound action potentials were recorded from the distal cut end of the tibial of a saphenous nerve following electro-acupuncture stimulation of the hindpaw. The mean threshold of the compound action potentials of the myelinated fibers in saphenous nerves was 0.18 mA, while that of unmyelinated fibers was 3.0 mA. The mean threshold of the compound action potentials of the myelinated fibers in the tibial nerve was 0.20 mA of unmyelinated fibers was 3.3 mA. Severance of bilateral trunks did not affect the response, while severance of the third cranial nerves abolished the responses. In conclusion, electro-acupuncture stimulation applied to the hindpaws of the anesthetized rats induced excitation of myelinated or of both myelinated and unmyelinated afferent fibers of the tibial and saphenous nerve, and involved a reflex response of pupil dilation through the third cranial parasympathetic efferent nerve.     

10 Gbit/s optical soliton transmission over 7200 km by using amonolithically integrated MQW-DFB-LD/MQW-EA modulator light source

The authors demonstrate 10 Gbit/s optical soliton transmission in a recirculating loop through the use of a monolithically integrated MQW-DFB-LD/MQW-EA modulator light source. The timing jitter due to the Gordon-Haus effect is successfully reduced by the optical bandpass filters conventionally used in the cascaded EDFAs to avoid the accumulation of amplified spontaneous emission. The transmission distance of 7200 km is achieved at a bit error rate of 10^-9     

Distributed self-stabilizing placement of replicated resources in emerging networks

Emerging large scale distributed networking systems, such as P2P file sharing systems, sensor networks, and ad hoc wireless networks, require replication of content, functionality, or configuration to enact or optimize communication tasks. The placement of these replicated resources can significantly impact performance. We present a novel self-stabilizing, fully distributed, asynchronous, scalable protocol that can be used to place replicated resources such that each node is "close" to some copy of any object. We describe our protocol in the context of a graph with colored nodes, where a node's color indicates the replica/task that it is assigned. Our combination of theoretical results and simulation prove stabilization of the protocol, and evaluate its performance in the context of convergence time, message transmissions, and color distance. Our results show that the protocol generates colorings that are close to the optimal under a set of metrics, making such a protocol ideal for emerging networking systems.     

Effects of different kind of sesame materials on the physical properties of gomatofu (sesame tofu)

Gomatofu (sesame tofu) is one of the traditional Japanese healthy foods and is representative of all shojin (vegetarian) dishes. Gomatofu, one of the mixed gels consisting of kudzu (arrowroot) starch and sesame, possesses an extremely unusual textural characteristic which is soft, smooth, and springy. The textural properties are greatly influenced by preparation, ingredients and roasting conditions of sesame seeds. Hence there are many kinds of sesame materials which can be used to prepare gomatofu such as white, black, huskless or not and roasted or unroasted sesame materials, in this study, the effects of these materials on the physical properties of gomatofu were studied. The sample of Ra-W prepared with unroasted huskless sesame seed had the least hardness, but mouthfeel of this sample were the highest. The samples of Ro-B and Ro-W prepared with roasted husk (black and white) sesame seed were evaluated to have the best palatability because of their superior springiness. It was clarified that different kinds of sesame materials affected the forming of structure and physical properties of gomatofu, because the chemical components were different from varieties of sesame materials.