Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

A novel cyclic process using CaSO4/CaS pellets for converting sulfur dioxide to elemental sulfur without generating secondary pollutants: Part II. Hydrogen reduction of calcium-sulfate pellets to calcium sulfide

The reduction of calcium sulfate to produce calcium sulfide is a part of the cyclic process for converting sulfur dioxide to elemental sulfur that is described in Part I. The kinetics of the hydrogen reduction of nickel-catalyzed calcium-sulfate pellets were investigated using a thermogravimetric analysis (TGA) technique at reaction temperatures between 1023 and 1088 K and hydrogen partial pressures between 12.9 and 86.1 kPa. The reactivity of nickel-catalyzed calcium-sulfate pellets was demonstrated by the conversion of 70 pct fresh nickel-catalyzed calcium sulfate to calcium sulfide in 20 minutes at 1073 K under a hydrogen partial pressure of 86.1 kPa. Furthermore, the reactivity remained relatively intact after ten cycles of reactions and regenerations. This observed characteristic of the pellets is important because the solids must be reusable for repeated cycles to avoid generating secondary pollutants. The nucleation and growth rate expression was found to be useful in describing the kinetics of the reaction, which had an activation energy of about 167 kJ/mol (∼40 kcal/mol) in all reaction cycles except for the first regenerated samples that were lower at 146 kJ/mol (35 kcal/mol). The reaction order with respect to hydrogen partial pressure was 0.22 in all cycles with the exception of the first regenerated sample for which it was 0.37.     

Improved Matrix-Filler Adhesion

Enhanced matrix-filler adhesion is realized after filler treatment with a surface treatment process. The hydrosol/coupling agent treatment was applied to a wide range of inorganic and organic fillers, and adhesion to a variety of matrix resins was improved. Scanning Electron Microscopy (SEM) was used to determine the locus of failure in the filled systems. The locus of failure shows the relative degree of adhesion between the filler and the polymer matrix. Significant improvement in adhesion in humid environments is also observed.     

Fast DCT algorithm with fewer multiplication stages

A novel fast DCT scheme with reduced multiplication stages and fewer additions and multiplications is proposed. The proposed algorithm is structured so that most multiplications tend to be performed at the final stage, which reduces the propagation error that could occur in the fixed-point computation. Minimisation of the multiplication stages can further decrease the error     

Mathematical and experimental investigation of the self-propagating high-temperature synthesis (SHS) of TiAl3 and Ni3Al intermetallic compounds

One-dimensional mathematical modeling was used to describe the self-propagating high-temperature synthesis (SHS) process for preparing TiAl₃ and Ni₃Al intermetallics. The kinetic parameters (activation energies and pre-exponential factors) for the two compounds were obtained by matching experimental measurement and the numerical solution. The results thus obtained were compared with rate parameters obtained using different methods. The activation energy was 483 and 283 kJ mol^?1 for the formation of TiAl₃ and Ni₃Al, respectively. The temperature profiles calculated using the mathematical model were compared with experimental measurements for both aluminides which indicated reasonable agreement. Fine particle size and moderate preheating increase the SHS rates.     

Kinetics of zinc oxide formation from zinc sulfide by reaction with lime in the presence of water vapor

A novel reaction scheme for transforming certain metal sulfides to the corresponding oxides has been developed. In this process, steam oxidizes the sulfide into the oxide, and the hydrogen sulfide produced reacts with lime to form calcium sulfide and regenerate steam. There is no net consumption or generation of gaseous species. Thus, the overall reaction can be carried out in a closed system as far as the gas phase is concerned. This eliminates the possibility of emitting hydrogen sulfide out of the reactor. Only certain metal sulfides are thermodynamically amenable to this treatment. In this paper, the reaction of ZnS to ZnO by this scheme is described, together with a detailed formulation of the rate equation for the overall reaction based on the kinetics of the component gas-solid reactions. Although the present work was done with CaO, other suitable oxides may be used in its place. A further potential application of this process is to the selective oxidation of certain sulfide(s) from complex sulfide ores as a treatment prior to the separation of minerals.     

BioFET sensor for detection of albumin in urine

Characterisation of a BioFET for detection of albumin in a mixture of human urine is presented. To avoid electrolyte effect of the urine, it was measured in PBS (phosphate buffer saline) at a fixed pH after albumin binding. The drain current was modulated by the albumin bound to the anti-albumin immobilised on the gate surface of the BioFET. The current variation ratio was likely to be proportional to the concentration of the albumin in the range 50-250 mg/1. The results show the feasibility of the BioFET as a urinary albumin sensor.     

An Inductively Coupled Lamb Wave Transducer

Wafer-type piezoelectric transducers are effective transducers for the excitation and detection of ultrasonic Lamb waves in plate-like structures. Such transducers are, however, vulnerable to corrosion and physical damage when mounted in exposed locations. In this paper we describe an inductively coupled Lamb wave transducer that eliminates the need for direct electrical connections. Signals are coupled into and out of the transducer using two probe coils. In this paper we explore the operation of inductively coupled transducers both analytically and experimentally. Finite-element analysis is used to determine inductances and the coupling constant, and electrical circuit analysis to determine the transfer function and its dependence on the gap between the probe coils and the transducer. Experiments show that return signals of millivolt amplitude are obtained when the transducer is excited with 10-V amplitude pulses. These transducers are suitable for permanent mounting on structures to be monitored for cracks or flaws     

Adaptive contour smoothing based on inter-region contrast

An adaptive contour smoothing algorithm designed as a preprocessor for shape coders is presented. In the method, the degree of the adaptive smoothing is controlled based on the significance of each contour point, which is quantified according to inter-region contrast in an intensity image. The actual smoothing consists of an expansion operator and a thinning algorithm.     

Computational Implementation of Asymmetric Integral Imaging by Use of Two Crossed Lenticular Sheets

We propose an asymmetric integral imaging method to adjust the resolution and depth of a three‐dimensional image. Our method is obtained by use of two lenticular sheets with different pitches fabricated under the same F/#. The asymmetric integral imaging is the generalized version of integral imaging, including both conventional integral imaging and one‐dimensional integral imaging. We present experimental results to test and verify the performance of our method computationally.