MODELING LIQUID MASS TRANSFER IN HIGEE SEPARATION PROCESS

Correspondence concerning this paper should be addressed to Professor Richard S.H. Mah. Hsien-Hsin Tung is now affiliated with Department of Chemical Engineering, California Institute of Technology

Penetration theory is used to describe the liquid mass transfer in Higee separation process. Within a possible range of effective areas, it is shown that the predicted mass transfer coefficients are in reasonable agreement with the estimated mass transfer coefficients. The estimated coefficients were calculated from the experimental data and the possible effective areas. Hence it is concluded the penetration theory is generally applicable to describe liquid mass transfer in Higee separation process. The comparison also suggests that liquid mixing at the junctions of packing materials may be more complete in Higee process than in traditional process.     

Living cationic polymerization of isobutyl vinyl ether (II): Photoinduced living cationic polymerization in a mixed solvent of toluene and diethyl ether

A new method of preparation of living cationic polymer of isobutyl vinyl ether via photoinduced polymerization in the presence of diphenyliodonium iodide (DPII, initiator) and zinc iodide in a mixed solvent of toluene/diethyl ether, which was irradiated at ?78°C for short period, was completed within 15 min. The reaction was allowed for further reaction in the dark until monomer was fully consumed. It was found that increase in the conversion of monomer to polymer during the irradiation is very limited. Confirmation of the linear dependence of number‐average molar mass of resulting polymer on % conversion together with the fact that polymerization proceeds until monomer consumption, and controllability of number‐average molar mass of resulting polymer, depending on the molar ratio of monomer and initiator, strongly suggests the living nature of this polymerization, unless reaction temperature becomes higher than 0°C, i.e., the absence of chain breaking process. The narrow molar mass distribution, whose polydispersity index values are less than 1.2, reveals that the rate of initiation where irradiation is usually completed within 15 min is much faster than that of propagation in cationic nature in this system. Effect of some major factors, such as solvent polarity and temperature, on the living nature of the polymerization was also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3581–3586, 2006     

Control of the leakage current in SrTiO3 films by acceptor doping

Stoichiometric SrTiO3 (STO) films doped with Fe or Cr were prepared by r.f. magnetron sputtering technique. The effects of Fe or Cr doping in the SrTiO3 films were studied on the leakage current property which was discussed by defect chemistry. The experimental results can be explained by a model in which oxygen vacancies are the key defects responsible for the leakage current. Acceptor doping, with a small concentration of Fe or Cr, has led to a substantial improvement to 10–9 order in the leakage current density. Above the concentration of 0.010.02 mol% Fe2O3, Cr2O3, however, as the concentration increased, the leakage current increased. These acceptors in Ti4+ site are expected to electrically compensate for donor species such as oxygen vacancies, thereby reducing the concentration of mobile carriers that contribute to electrical conduction. Consequently, acceptor doped STO films have been shown to be superior to undoped films for applications requiring high leakage resistance, such as dynamic random access memory capacitors. © 1998 Chapman & Hall     

Modelling and management of smart microgrid for rural electrification in sub-saharan Africa: The case of Nigeria

Access to electricity is still a challenge in many parts of sub-Saharan Africa. In Nigeria, over 70% of the rural dwellers do not have access to electricity. The purpose of this paper is to examine the potential of a smart microgrid for off-grid rural electrification in Nigeria. A combination of design thinking and model-based design methodology is employed to select a suitable microgrid configuration and to develop a smart microgrid model. A system consisting of a solar photovoltaic array, battery energy storage and a diesel generator is selected, and the model is developed in Simulink. Demand data from 10 rural communities in Nigeria are used to validate the performance of the model and the potential for demand management is considered. The use of energy efficient light bulbs is found to reduce the peak electricity demand of the case study communities by 42 to 76%. Combining the proposed system with the use of LED bulbs makes the system to have 56 to 81% less net present cost than a system with a diesel generator alone and incandescent light bulbs. The proposed smart microgrid is found to be more suitable for off-grid rural electrification in Nigeria than diesel generators which are currently used for off-grid electrification in Nigeria.     

Leachability of degradation products from hard chairside reline resins in artificial saliva: Effect of water‐bath post‐polymerization treatment

The effect of a post‐polymerization treatment on the leaching of methacrylic acid (MA) and benzoic acid (BA) from the reline resins [Kooliner (K), New Truliner (N), Ufi Gel hard (U), and Tokuso Rebase Fast (T)] was evaluated. Specimens of each material were divided into two groups: Group C (control) – left untreated; Group WB (water‐bath) – immersion in water at 55 ± 1°C for 10 min. Specimens were placed in artificial saliva at 37 ± 1°C and, after 1‐, 3‐, 5‐, 24‐h and 3‐, 7‐, 14‐, and 30‐day intervals, aliquots were removed and analyzed using high performance liquid chromatography. Data were analyzed by using Wilcoxon, Mann–Whitney or Kruskal–Wallis tests (α = 0.05). At 1 h, the concentration of MA released from U control specimens was higher than those of the other ones, and decreased after 3 h. WB specimens released lower amounts of MA than control specimens only for material U, at the 1‐ and 3‐h periods. For all control specimens, concentrations of leached BA progressively decreased within 5 h and from 24 h to the end. WB specimens released significantly lower amounts of BA than did the control groups. The highest concentration of MA was leached from control specimens of Ufi Gel hard. Water‐bath post‐polymerization treatment caused a significant reduction in elution of BA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The ability of zinc to inhibit the sporulation and viability of Clostridium sporogenes and growth of other bacteria

The objective of this study was to investigate the influence of zinc on the sporulation and viability of Clostridium sporogenes and on the growth of other bacteria. When 0.5% ZnCl₂ was added to a sporulation medium, it completely inhibited C. sporogenes (PA 3679) sporulation for up to 3 weeks. At concentrations of 0.5% and 1.0%, ZnCl₂ not only completely inactivated the vegetative cell viability (>7.0 Log reduction) but also significantly reduced the spore viability (<2.1 Log reduction) of C. sporogenes. Taken together, it was concluded that zinc blocks C. sporogenes sporulation by damaging (or killing) vegetative cells and probably by interfering with the biosynthesis of spore components. In addition to the inhibitory effect on the sporulation and viability of C. sporogenes, ZnCl₂ was found to have a broad antimicrobial spectrum against all Gram‐positive and Gram‐negative spoilage and pathogenic bacteria tested. The minimal inhibitory concentration for inhibiting the bacteria ranged between 3.7 and 7.4 mm . Therefore, we expect that this compound or a combination thereof has a potential as a surface‐cleaning agent or disinfectant.     

Synthesis and characterization of magnetic and fluorescent styrene co‐polymer nanofiber

F luorescent and magnetic poly(styrene) (PS) based random co‐polymer nanofiber was synthesized in a controlled manner via chemical polymerization in three steps. A fluorescent and magnetic nanohybrid {Fe₃O₄/Congored (CR)} was separately prepared and chemically grafted onto the epichlorohydrin (ECH) units of the random co‐polymer. Characterizations of the above synthesized polymers were done with the help of Fourier transform infrared (FTIR) spectroscopy, UV–visible spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, fluorescence emission spectroscopy, field emission scanning electron microscopy (FESEM), scanning electron microscopy (SEM), vibrating sample magnetometer (VSM) measurement, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and gel permeation chromatography (GPC) like analytical techniques. The FESEM results indicated that after the grafting of nanohybrid onto the random co‐polymer backbone, the polymer exhibited a nanofiber like morphology. Due to the surface functionalization and encapsulation reactions, the magnetic moment value of the nanohybrid and its nanocomposites were found to be reduced. Synthesis and characterization of magnetic and fluorescent random co‐polymer based nanofiber is the primary target of the present investigation and its application is extended to the catalysis field. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42796.     

Angiotensin-I-converting enzyme inhibitory activity and bitterness of enzymatically-produced hydrolysates of shrimp (Pandalopsis dispar) processing byproducts investigated by Taguchi design

The importance of water-to-substrate ratio, protease type, percent enzyme and incubation time on hydrolysates produced from shrimp processing byproducts was investigated using Taguchi’s L₁₆ (4⁵) experimental design. Protease type significantly (p < 0.05) influenced soluble yield, degree of hydrolysis (DH), angiotensin-I-converting enzyme (ACE) inhibitory activity and bitterness of hydrolysates, while percent enzyme only affected the DH. Hydrolysates produced by Alcalase and Protamex possessed strong ACE inhibitory activity (IC₅₀ = 100–200 μg/ml and 70 μg/ml, respectively), accompanied by high yield, high DH and strong bitterness. Furthermore, ACE inhibition was positively correlated (r² = 0.87) with bitterness of the hydrolysates. Fractionation by size-exclusion chromatography revealed that the bitter substances, which also showed strong ACE inhibition, were <3 kDa in size and contained many hydrophobic residues, including Tyr, Phe, Leu, Ile, Val and Lys. Despite the bitterness, these hydrolysates may have potential health benefits, arising from their potent ACE inhibitory activity.