Anthocyanin composition of the red wine Babić affected by maceration treatment

Identification of anthocyanins in the wine made of the Croatian autochthonous grape variety of Babić (Vitis vinifera L.) was carried out and their profile was determined by means of high-performance liquid chromatography with diode array and mass spectrometric detection. Dependence of anthocyanins content and profile on maceration treatment conditions was investigated. Statistically significant differences of anthocyanins concentration in wines Babić produced by various maceration treatments were confirmed by the use of multivariate analysis of variances. The investigation results indicated that the maceration temperature exerts higher influence on anthocyanins concentration than the duration of maceration. In addition, on the basis of anthocyanin composition and using different multivariate statistical analyses, differentiation of wines Babić according to maceration treatments was procured.     

Clinical study in epidural injection with lappaconitine compound for post-operative analgesia

In this study, the effect and side-effect of epidural injection with lappaconitine compound for post-operative analgesia was observed. One hundred and twenty patients were randomly divided into 4 groups. Lappaconitine compound (LB) consisted of 12 mg of lappaconitine and 22.5 mg of bupivacaine, was given to group A (the group of observation), and lappaconitine 12 mg, bupivacaine 22.5 mg and morphine 2 mg to group B, C and D respectively for control. All were given by epidural injection with single blind method during post-operative pain of incision operation. Result showed that the initiating of analgesia was quicker in group A and C than that in group B and D, and the efficacy was group D > A > C > B. There was significant difference between group A and B in the above two parameters, P < 0.01 and P < 0.05. The analgisia maintenence time of single injection was D > A > B > C, that of group D was significantly longer than that of group A (P < 0.01). It indicated that the epidural injection with LB was more rapid and potent than that with lappaconitine alone in post-operative analgesia, and the former had no side-effect, it was safer than morphine.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

An approach to efficient business intelligent system for financial prediction

A concept of business intelligent system for financial prediction is considered in this paper. It provides data needed for fast, precise and good business decision support to all levels of management. The aim of the project is the development of a new online analytical processing oriented on case-based reasoning (CBR) where a previous experience for every new problem is taken into account. Methodological aspects have been tested in practice as a part of the management information system development project of “Novi Sad Fair”. A case study of an improved application of CBR in prediction of future payments is discussed in the paper. This paper is originally presented at The International Conference on Hybrid Information Technology 2006, at the special session on “Intelligent Information Systems for Financial Engineering”, November 2006 in Cheju Island, Korea.     

Design and implementation of clinical trials of antimicrobial drugs and devices used in periodontal disease treatment

The design and implementation of clinical trials (CTs) carried out to evaluate antimicrobial and anti-infective drugs and devices are one of the most difficult challenges in contemporary periodontal research and product development. The overwhelming amount of evidence which has established a microbial etiology for periodontitis is the basis for developing and testing antimicrobial treatments. Well-designed antimicrobial CTs start with a carefully crafted hypothesis and a protocol which explicitly integrates the requirements of the patient, the clinician, the sponsor, and regulatory authorities. Surrogate variables for effectiveness must be clinically relevant, scientifically sound, and statistically valid. Currently, clinical attachment level measurements and alveolar bone assessments are accepted as proof of effectiveness. Indication and claim support of the antimicrobial product guide the design and implementation of the CT. Adverse microbiologic consequences, such as lack of antimicrobial susceptibility, wrong spectrum, incorrect dosage, non-compliance, and drug interference, must be monitored. Successful CTs balance a large group of variables used to screen, randomize, and assign subjects to experimental and control groups to ensure that prognostic and risk factors are properly accounted for.