Fine Dry Grinding of Zeolite in a Laboratory Ball Mill

This paper presents the importance and usage of natural zeolites, which was recently recognized in the industry. Therefore, the grinding properties of natural zeolite were studied with the emphasis on a kinetic study in a ball mill. The experimental mill employed was laboratory sized, 200 mm diameter, 191 mm length, providing a total mill volume of 6000 cm³, with a total mass of 5.62 kg of steel balls of 25 mm diameter with a charge of 20% of the mill volume and with a rotation speed of 76 rpm. The breakage parameters were determined by using single sized feed fractions of ?850+600 μm, ?600+425 μm, and ?425+300 μm for the zeolite samples. The S_i (specific rate of breakage) and B_{i, j} (primary breakage distribution) values were obtained for those feed size fractions in order to predict the product size distributions by simulation for comparison to the experimental data. From the experimental results, S_i values increased as the feed sizes became coarser, i.e., the highest S_i value was 0.85 min^?1 for ?850+600 μm, while the lowest S_i value was 0.65 min^?1 for ?425+300 μm feed ground in the mill. The B_{i, j} values obtained for the zeolite sample were γ=0.84, ?=0.61, and β=4.25. The breakage parameters obtained showed that the zeolite is broken faster than quartz and slower than calcite and barite in terms of the a_T values reported previously at the same experimental conditions. The simulations of the product size distributions of zeolite were in good agreement with the experimental data using a standard ball mill simulation program. The slowing‐down effect was also seen in the mill after 4 min. of grinding.     

Characterization of active sites over reduced Ni-Mo/Al(2)O(3) catalysts for hydrogenation of linear aldehydes

Reduced Ni-Mo/Al(2)O(3) catalysts exhibit a behavior analogous to that of sulfided Ni-Mo/Al(2)O(3) catalysts in hydrogenation of linear aldehydes to alcohols. Similar to what has been previously reported for sulfided catalysts, NO and CO(2) can be used over the reduced Ni-Mo catalysts as probe molecules for the active sites responsible for two competing reactions -- aldehyde hydrogenation to alcohols and condensation reactions to heavy products, respectively. Reduced catalysts have a higher aldehyde conversion activity and alcohol selectivity than their sulfided counterparts. The reduction temperature has a strong effect on the surface density of anion vacancies, which are responsible for alcohol formation. Reduction temperature also plays a role in determining the abundance of OH groups on the alumina surface. The effect of reduction temperature also manifests itself through the differences seen in the oxidation states of Mo and Ni species.     

Determination of the critical surface tension of wetting of minerals treated with surfactants by shear flocculation approach

This paper contributes the shear flocculation method as a new approach to determine the critical surface tension of wetting of minerals treated with surfactants. This newly developed approach is based on the decrease of the shear flocculation of the mineral suspension, with decreasing of the surface tension of the liquids used. The solution surface tension value at which shear flocculation does not occur can be defined as the critical surface tension of wetting (gamma c) of the mineral. By using the shear flocculation method, the critical surface tensions of wetting (gamma c) for calcite and barite minerals, treated with surfactants, were obtained as 30.9 and 35.0 mN/m, respectively. These values are in good agreement with data reported previously on the same minerals obtained by the contact angle measurement and flotation methods. The chemical agents used for the treatment of calcite and barite particles were sodium oleate and sodium dodecyl sulfate, respectively.     

Neuron-based microarray sensors for environmental sensing

We present a novel sensing scheme for detecting the effects of unburned fossil fuels by integrating microarray technology and dielectrophoresis to develop single-neuron arrays. These arrays have the capability to sense and identify the two fuels, at parts per billion (ppb) concentrations, as well to determine the associated physiological changes at the single-cell level. Identification is achieved through frequency domain analysis of the measured changes to the extracellular electrical activity due to the effect of the fossil fuels. This yields unique electrical identifiers known as "signature patterns". Simultaneous optical visualization to the physiological changes is obtained by specific fluorescent staining. The correlation between the signature patterns and the cellular biological behavior establishes the veracity of this identification technique.     

Reactions of 1S, 1D,and 3P carbon atoms with water. Oxygen abstraction and intermolecular formaldehyde generation mechanisms; An MCSCF study

Reactions of singlet and triplet carbon atoms with water are explored theoretically using CASSCF–MCQDPT2, CCSD, and DFT methodologies. The ¹S carbons are found to be unreactive. Depending on the carbon atom generation method and the reaction medium, gas‐phase C(³P) attacking water may generate CO and atomic hydrogen as the end products. Reaction paths of the C(¹D) + H₂O system are complicated due to the involvement of two reactive potential energy surfaces with branchings occurring along each. Modifications in product distributions for reactions taking place in condensed phases are elaborated. The decisive reaction conditions, under which the oxygen abstraction and intermolecular formaldehyde generation dominate, are suggested to clarify the discrepancy related with experimental CO observation. The findings are consistent with available experimental data on this system. Oxygen abstraction and intermolecular formaldehyde generation mechanisms suggested here are capable of serving as models for similar reactions of alcohols. © 2011 Wiley Periodicals, Inc. Int J Quantum Chem, 2012     

A Sensitive and Selective RP-LC Method for the Simultaneous Determination of the Antihypertensive Drugs,Enalapril, Lercanidipine,Nitrendipine and Their Validation

A RP-LC method is presented, which is sensitive and selective for the simultaneous determination of enalapril–lercanidipine and enalapril–nitrendipine binary mixtures in their pharmaceutical dosage forms. The analyte peaks were detected using the LC method with the mobile phase ratio of methanol: water (70:30 v/v, pH 3.0) and a 1.0 mL min⁻¹ flow rate. The detection wavelength was selected at 210 nm using photo diode array detector and column temperature was optimized to 30 °C. Linearity was obtained at different concentration ranges for all working pharmaceutically active compounds between 0.5 and 25 μg mL⁻¹. The proposed methods were extensively validated according to USP 27 requirements and ICH guidelines. The methods were applied to the analysis of pharmaceutical dosage forms containing binary mixtures of enalapril–lercanidipine and enalapril–nitrendipine. Moreover, the proposed methods were applied for the degradation studies of the selected compounds. Degradation studies were conducted using stress conditions such as UV light, acidic and alkaline hydrolysis, oxidation and heat in oven, to evaluate the ability of the separation of the response of standard compounds from their degradation products.

     

Electrochemical investigation and determination of ceftazidime in pharmaceutical dosage forms and human urine

A voltammetric study of the oxidation of Ceftazidime (CEFT) has been carried out at the glassy carbon electrode by cyclic, differential pulse (DPV) and square wave (SWV) voltammetry. The oxidation of CEFT was irreversible and exhibited diffusion controlled process depending on pH. The oxidation mechanism was proposed and discussed. According to the linear relationship between the peak current and concentration, DPV and SWV voltammetric methods for CEFT assay in pharmaceutical dosage forms and human urine were developed. For analytical purposes, a well resolved diffusion controlled voltammetric peak was obtained in 0.1 M H₂SO₄ at 1.00 and 1.02 V for differential pulse and square wave voltammetric techniques, respectively. The linear response was obtained within the range of 4 × 10^?6?8 × 10^?5 M with a detection limit of 6 × 10^?7 M for differential pulse and 4 × 10^?6–2 × 10^?4 M with a detection limit of 1 × 10^?6 M for square wave voltammetric technique. The determination of CEFT in 0.1 M H₂SO₄ was possible over the 2 × 10^?6–1 × 10^?4 M range in urine sample for both techniques. The standard addition method was used for the recovery studies.     

Determination of phenytoin in exhaled breath condensate using electromembrane extraction followed by capillary electrophoresis

Application of hollow fiber-based electromembrane extraction was studied for extraction and quantification of phenytoin from exhaled breath condensate (EBC). Phenytoin is extracted from EBC through a supported liquid membrane consisting of 1-octanol impregnated in the walls of a hollow fiber, and into an alkaline aqueous acceptor solution inside the lumen of the fiber. Under the obtained conditions of electromembrane extraction, that is, the extraction time of 15 min, stirring speed of 750 rpm, donor phase pH at 11.0, acceptor pH at 13.0, and an applied voltage of 15 V across the supported liquid membrane, an enrichment factor of 102-fold correspond to extraction percent of 25.5% was achieved. Good linearity was obtained over the concentration range of 0.001–0.10 µg/mL (r² = 0.9992). Limits of detection and quantitation were 0.001 and 0.003 µg/mL, respectively. The proposed method was successfully applied to determine phenytoin from EBC samples of patients receiving the drug. No interfering peaks were detected that indicating excellent selectivity of the method. The intra- and interday precisions (RSDs) were less than 14%.