Objective approach for analysis of noise source characteristics and acoustic conditions in noisy computerized embroidery workrooms

It is highly important to analyze the acoustic properties of workrooms in order to identify best noise control measures from the standpoint of noise exposure limits. Due to the fact that sound pressure is dependent upon environments, it cannot be a suitable parameter for determining the share of workroom acoustic characteristics in producing noise pollution. This paper aims to empirically analyze noise source characteristics and acoustic properties of noisy embroidery workrooms based on special parameters. In this regard, reverberation time as the special room acoustic parameter in 30 workrooms was measured based on ISO 3382-2. Sound power quantity of embroidery machines was also determined based on ISO 9614-3. Multiple linear regression was employed for predicting reverberation time based on acoustic features of the workrooms using MATLAB software. The results showed that the measured reverberation times in most of the workrooms were approximately within the ranges recommended by ISO 11690-1. Similarity between reverberation time values calculated by the Sabine formula and measured values was relatively poor (R ²?=?0.39). This can be due to the inaccurate estimation of the acoustic influence of furniture and formula preconditions. Therefore, this value cannot be considered representative of an actual acoustic room. However, the prediction performance of the regression method with root mean square error (RMSE)?=?0.23 s and R ²?=?0.69 is relatively acceptable. Because the sound power of the embroidery machines was relatively high, these sources get the highest priority when it comes to applying noise controls. Finally, an objective approach for the determination of the share of workroom acoustic characteristics in producing noise could facilitate the identification of cost-effective noise controls.     

Coral assemblages in Tonga: spatial patterns, replenishment capacities, and implications for conservation strategies

Coral reefs in Tonga have been confronted by multiple threats of various origins, including large-scale disturbances and human-induced stressors. These reef communities have been poorly studied, and efficient conservation actions are urgently needed. The aim of this study was to: (1) examine the spatial distribution of coral assemblages in the lagoon of Tongatapu; (2) determine the degree to which spatial heterogeneity of adult corals is influenced by recruitment processes; and (3) examine the implications of these results in terms of conservation actions. We recorded a total of 37 adult and 28 juvenile coral genera, a mean density of 11.6 adult and 5.5 juvenile colonies m^?2, and a dominance of Montipora, Acropora, and Porites. For seven of the 10 dominant genera, spatial patterns of adults were linked to the short-term recruitment pattern history. Despite a reduced diversity and abundance of adult corals in some areas, the lagoon of Tongatapu retains the potential for replenishment through recruitment of young corals. Consequently, we suggest that conservation actions should focus on reducing factors causing coral mortality and maintain suitable conditions for the establishment and growth of juvenile corals, thus increasing the probability that they will reach maturity and participate to the maintenance of local populations. Rather than establishing a large marine protected area, which will almost certainly suffer from a lack of control and poor enforcement, alternative conservation measures could be successfully implemented through the establishment of several small village-based marine reserves, as has been undertaken in other South Pacific islands with promising results.     

Usage of polystyrene disposable food dishes in the lightweight concrete making

The increasing use and subsequent accumulation of polystyrene containers has triggered a substantial environmental problem. This study investigated using varied percentages of solid waste polystyrene disposable food dishes in the production of lightweight concrete samples with 350 kilograms per cubic meter (kg/m³) of cement and a density of 1,300 kg/m³. The polystyrene disposable dishes were ground into beads of 0–3 millimeters (mm) and 3–6 mm in size. First, the characteristics of Type II Portland cement, polystyrene, and aggregates were examined. The following characteristics of concrete using ASTM International and British Standards Institution standards were tested: slump, compressive strength, ability to resist chloride ion penetration, and resistance of concrete to rapid freezing and thawing cycles. Scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy analytical techniques were also used. The slump of samples varied between 40 and 70 mm and was not dependent on either the polystyrene percentage or the size of the polystyrene beads in the concrete samples (p‐value > .05). The compressive strength of the concrete samples after 90 days of curing, and using different percentages of polystyrene, varied between 96 and 113 kilograms per square centimeter (kg/cm²). The resistance of the samples to the freezing and thawing cycle and chloride ion penetration were affected unfavorably by the presence of the polystyrene. The SEM technique indicated that concrete samples containing 15% and 25% polystyrene had denser crystals and less void than concrete samples with 40% and 55% polystyrene.     

The effect of greenhouse vegetation coverage and area on the performance of an earth-to-air heat exchanger for heating and cooling modes

The underground temperature at a depth of about 3–4 m is almost constant all the year round. In summer, the underground temperature is lower than the ambient temperature, but in winter it is vice versa. This potentiality is considered for greenhouse cooling and heating by using an earth-to-air heat exchanger (EAHE). This paper considers the effects of two parameters as independent variables including the area of greenhouse and the percentage of vegetation coverage inside the greenhouse on the performance of an EAHE system during both cooling and heating modes. The inside temperature, the thermal energy exchange and the coefficient of performance (COP) of the system were considered as dependent variables. The results showed that both greenhouse area and the percentage of vegetation coverage inside the greenhouse had significant effects on the performance of the EAHE system during both cooling and heating modes. However, the COP of the EAHE system was higher in the cooling mode (4.32) than during the heating mode (1.01). The percentage of vegetation coverage negatively affected the performance of the EAHE system in the cooling mode. However, the performance of the EAHE system improved with the increase in the percentage of vegetation coverage during the heating mode.     

Groundwater geochemistry in the Alisadr, Hamadan, western Iran

The chemical composition of 59 well water samples throughout the Alisadr area, Hamadan, western Iran was determined in order to describe the background ion concentration and to identify the major hydrogeochemical processes that control the observed groundwater chemistry. The hydrochemical types, Ca–HCO₃, Ca–SO₄, dominate the largest part of the groundwater followed by water types Ca–Cl and Mg–HCO₃. Total hardness indicated that 30% of groundwater samples fell in the very hard water category. Ninety-seven percent of the water samples showed nitrate ( ${\rm NO}_{3}^{-})$ concentrations above the human affected value (13 mg l^???1 ${\rm NO}_{3}^{-})$ , while 15% exceeded the maximum acceptable level (50 mg l^???1 ${\rm NO}_{3}^{-})$ according to WHO regulations. With respect to sodium adsorption ratio, the groundwater can be used for irrigation on almost all soils with little danger of the developing harmful levels of exchangeable Na^?+?. But with respect to electrical conductivity, the water quality for irrigation was low to medium, providing the necessary drainage to avoid the buildup of toxic salt concentrations. Geochemical modeling using PHREEQC enabled prediction of the saturation state of minerals and indicated the dissolution and precipitation reactions occurring in the groundwater. Groundwaters were undersaturated with respect to amorphous silica. Stability diagram indicated that the dominant cluster of groundwater samples fell into the K-feldspar field.     

Operational leeway in work situations: do ergonomic risk assessment tools consider operational leeway for job analysis?

Our study shows that information on operational leeway is limited in the originator articles of the ergonomic risk assessment tools for prevention of musculoskeletal disorders (MSDs). The tools’ underlying theoretical models do not consider the indicators of operational leeway, and they cannot determine the sufficiency of the situational operational leeway in a work situation. Consequently, regulation of the activity, which ensures the performance goals and the individual's health, has been overlooked. The lack of literature on indicators of situational operational leeway is one of the reasons for this deficit. Defining the indicators for this concept would be an innovation in the approach of MSD risk prevention. Developing empirically the concept of situational operational leeway in risk assessment tools would help to progress the current approach of MSD prevention. This study therefore proposes indicators of situational operational leeway to increase the representativeness and reliability of the risk assessment tools for MSDs.     

Involvement of mitochondrial-mediated caspase-3 activation and lysosomal labilization in acrylamide-induced liver toxicity

Acrylamide (ACR) is a chemical frequently used in both industrial and synthetic processes and may be produced during food processing. ACR at very high concentrations is postulated to exert its toxicity through the stimulation of an oxidative stress. ACR in excessive doses induces the central nervous system, reproduction, and genetic toxicity. However, ACR effects on the liver, a major organ of drug metabolism, have not been adequately explored. In addition, the role of mitochondria in an ACR-mediated hepatotoxicity is still unclear. The aim of this study was to investigate the cytotoxic mechanisms attributed to ACR using isolated rat hepatocytes. Hepatocytes were isolated by the collagenase perfusion method and incubated with an EC50_2hr concentration of ACR for 3 hr. The EC50_{2 hr} of ACR on isolated rat hepatocytes was determined to be 1 mM. Based on our results, hepatocytes cytotoxicity of ACR (1 mM) was mediated by a reactive oxygen species formation and lipid peroxidation. Incubation of hepatocytes with ACR produced rapid hepatocyte glutathione depletion which is another marker of the cellular oxidative stress. ACR cytotoxicity was also associated with mitochondrial injury as evidenced by the decline of mitochondrial membrane potential and lysosomal membrane leakiness. Our results also showed that ACR induced caspase-3 activation, the final mediator of apoptosis signaling. These findings contribute to a better understanding underlying mechanisms involved in ACR hepatotoxicity originating from the oxidative stress and ending in mitochondrial/lysosomal damage and cell death signaling.     

Biodegradation of low-density polyethylene (LDPE) by isolated fungi in solid waste medium

In this study, biodegradation of low-density polyethylene (LDPE) by isolated landfill-source fungi was evaluated in a controlled solid waste medium. The fungi, including Aspergillus fumigatus, Aspergillus terreus and Fusarium solani, were isolated from samples taken from an aerobic aged municipal landfill in Tehran. These fungi could degrade LDPE via the formation of a biofilm in a submerged medium. In the sterilized solid waste medium, LPDE films were buried for 100 days in a 1-L flask containing 400 g sterile solid waste raw materials at 28 °C. Each fungus was added to a separate flask. The moisture content and pH of the media were maintained at the optimal levels for each fungus. Photo-oxidation (25 days under UV-irradiation) was used as a pretreatment of the LDPE samples. The progress of the process was monitored by measurement of total organic carbon (TOC), pH, temperature and moisture. The results obtained from monitoring the process using isolated fungi under sterile conditions indicate that these fungi are able to grow in solid waste medium. The results of FT-IR and SEM analyses show that A. terreus and A. fumigatus, despite the availability of other organic carbon of materials, could utilize LDPE as carbon source. While there has been much research in the field of LDPE biodegradation under solid conditions, this is the first report of degradation of LDPE by A. fumigatus.     

The detection of SARS-CoV-2 RNA in indoor air of dental clinics during the COVID-19 pandemic

Environmental Science and Pollution Research - In the indoor environment of dental clinics, dental personnel and patients are exposed to a risk of infection because of the transmission of...