Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Microwave-Assisted Graphite-Support Synthesis of Imidazolones

5(4H)-Oxazolones react with ammonium acetate under microwave irradiation and using graphite as support in an eco-friendly process. The reaction was carried out under solvent-free conditions and the imidazolones were obtained quantitatively. Moreover the reaction time was reduced too.     

An adaptive tracking problem for a family of retarded time-delay plants

Most of the existing switching control techniques are developed specifically for finite-dimensional linear time-invariant (LTI) systems. In many practical applications, however, it is essential to take time delay into consideration in the modelling as the control system can be highly sensitive to delay. In this paper, a multi-model switching control algorithm is proposed for retarded time-delay systems. It is assumed that the plant is represented by a family of known multi-input multi-output, observable, LTI models with multiple delays in the states, and that corresponding to each model in the known family, there exists a high-performance finite-dimensional LTI controller. In addition, it is supposed that a bound on the magnitude of the external inputs and disturbances is available. It is then shown that the proposed switching controller can stabilize the uncertain system, and that under some mild conditions, output tracking can be achieved in the given problem setting. Copyright © 2007 John Wiley & Sons, Ltd.     

Computerized facility layout design

The paper describes a computerized facility layout designer, COMLAD II, for plant layout development. Besides developing an efficient layout, COMLAD II has useful features which allow fixing the departments, changing the shape of the departments and changing the length and width dimensions of the overall layout.     

An automated coding and classification system with supporting database for effective design of manufacturing systems

The philosophy of group technology (GT) is an important concept in the design of flexible manufacturing systems and manufacturing cells. Group technology is a manufacturing philosophy that identifies similar parts and groups them into families. Beside assigning unique codes to these parts, group technology developers intend to take advantage of part similarities during design and manufacturing processes. GT is not the answer to all manufacturing problems, but it is a good management technique with which to standardize efforts and eliminate duplication. Group technology classifies parts by assigning them to different families based on their similarities in: (1) design attributes (physical shape and size), and/or (2) manufacturing attributes (processing sequence). The manufacturing industry today is process focused; departments and sub units are no longer independent but are interdependent. If the product development process is to be optimized, engineering and manufacturing cannot remain independent any more: they must be coordinated. Each sub-system is a critical component within an integrated manufacturing framework. The coding and classification system is the basis of CAPP and the functioning and reliability of CAPP depends on the robustness of the coding system. The proposed coding system is considered superior to the previously proposed coding systems, in that it has the capability to migrate into multiple manufacturing environments. This article presents the design of a coding and classification system and the supporting database for manufacturing processes based on both design and manufacturing attributes of parts. An interface with the spreadsheet will calculate the machine operation costs for various processes. This menu-driven interactive package is implemented using dBASE-IV. Part Family formation is achieved using a KAMCELL package developed in TURBO Pascal.     

Influence of joint detail on the flexural/torsional interaction of thin-walled structures

For a structure formed from two thin-walled open members connected at 90°, torsion applied to one member can result in torsion as well as flexure in the second member, with the magnitude and direction of this torsion as well as flexure in the second member being determined by the type of joint used. Conventional structural analysis would normally assume the presence of only flexure in the second member. The results from a finite element study of structures formed from thin-walled channel sections connected by box, mitre and stiffened mitre joints is presented and an explanation for the behaviour of the different joint types is given. It is shown that for the box joint the warping deformation of the loaded member is the dominant factor in determining the magnitude and direction of the twisting of the second member, whilst this is determined for the stiffened mitre joint primarily by the St Venant rotation deformation of the loaded member. For the unstiffened joint it is shown that the warping and St Venant rotation deformation effects tend to cancel each other out.     

Variation in phosphoric acid concentration and treatment time and HEMA diffusion through dentin

IGF-1 and its receptors have been identified in many tissues including the central nervous system (CNS). We have previously demonstrated that injection of insulin directly into the cerebral ventricles (ICV) is followed by a drop in mean arterial pressure (MAP) associated with an increase in skeletal muscle blood flow. Given the similarities between the IGF-1 and insulin molecules and their respective receptors, we have investigated the effect of ICV administration of IGF-1 on systemic blood pressure and blood flow in selected vascular beds. ICV cannulas were implanted into normal rats and the animals were allowed to recover for 3 to 4 days. The femoral artery and vein were cannulated for blood pressure monitoring and blood sampling and blood flow probes placed around the iliac, the renal and the superior mesenteric artery were used to assess regional blood flow. ICV injection of IGF-1 resulted in a significant decrease in MAP with a nadir at 15 minutes and a gradual return to baseline by 60 minutes; heart rate increased 40 minutes after the injection. IGF-1 significantly enhanced vascular flow and conductance in the iliac, but not in the renal and superior mesenteric arteries. The effects of IGF-1 were much smaller than those observed previously with equimolar amounts of insulin. We conclude that IGF-1 can decrease MAP by selectively increasing blood flow to skeletal muscle through a direct action on the central nervous system.     

Application of outranking methods to economic and financial justificaton of CIM systems

Traditional economic evaluation methods concentrate on maximizing or minimizing a single objective such as net present value and pay back period. In the last decade, there has been an increased awareness of the need to consider multiple attributes in the evaluation of advanced manufacturing systems. Various methods have recently been developed for the evaluation of CIM systems. This paper discusses multiattribute methods for justification of CIM systems and outranking methods including ELECTRE, ORESTE, and PROMETHEE.     

Influence of fretting on the fatigue strength at the vise clamp-specimen interface

Fretting fatigue is one of the most important phenomena for inducing a significant reduction of fatigue strength and consequently, leading to unexpected failure accidents of the engineering structures even at very low stresses. In the present study, both plain and fretting fatigue tests with zero mean stress were carried out on two different types of steel, low-carbon steel and martensitic stainless steel, by means of a reversed bending fatigue testing machine. The drop in the fatigue strengths through fretting at vise clamp-specimen interface were significant for both tested steels. The fretting processes produced a reduction in fatigue strength of about 27% for low-carbon steel and 16% for martensitic stainless steel.     

The sinuous antenna-A dual polarized feed for reflector-based searching systems

The sinuous antennas have a numerous applications in military and civil systems such as direction finding systems and reflector feeds due to their superior broadband characteristics and simultaneous polarization capability. In this paper, design, construction and measurements of planar sinuous antennas are investigated for 1–5 GHz frequency range. Feeding sections of this antenna are realized by using microstrip tapered baluns. We have determined the microstrip tapered balun dimensions using Ansoft HFSS-simulation program. The performances of the manufactured antenna are measured using HP vector network analyzer. Polarization patterns and return loss characteristics of the designed antenna that have been measured in anechoic chamber, are presented.