Shape Optimization of Elliptical Road Containers Due to Liquid Load in Steady-State Turning

A numerical analysis of liquid load in elliptical road containers undergoing a steady-state turning manoeuvre is presented for containers of unrestricted size and for containers of fixed capacity. The liquid load is expressed in terms of the horizontal and vertical forces and the overturning moment created by these forces around the middle bottom point of the container. The moment is obtained by integrating the liquid free-surface equation and using numerical calculation of the resulting expressions. An optimization study with an objective to minimize the peak overturning moment is performed on containers of fixed capacity to identify the optimal height/width ratio of the container. The results of this investigation being of a general nature, i.e. with no restriction for an application, are particularly intended for road tankers under a steady turning manoeuvre, where they can be applied with high degree of accuracy.     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

Development of Green-Naghdi models with a wave-absorbing beach for nonlinear, irregular wave propagation

Two-dimensional and three-dimensional Green-Naghdi (GN) models equipped with a numerical wave-absorbing beach have been developed to simulate nonlinear, regular, and irregular wave propagation. The numerical beach is introduced near the downstream boundary to absorb outgoing waves. An appropriate amount of numerical damping and an appropriate length of numerical beach are investigated using numerical experiments. The results show that the GN models with a numerical beach work very well in simulating wave propagation in water in a small computational domain.     

Effect of fatigue strain range on properties of high-strength structural steel

Ship hulls are built with stiffened steel plates and experience continuous fatigue load cycles when in service. Mechanical properties of the steel are expected to change due to the application of these cyclic loads. Therefore, the mechanical properties of the material at various levels of fatigue damage need to be understood. This paper presents two test series that were conducted to determine the effect of two different strain ranges (2000 and 3000 micro strains) of fatigue cycles on the mechanical properties of high-strength structural steel. The test results indicate that the cycle-dependent behaviours of the material can cause a slight increase or a significant decrease in the yield strength when compared to its virgin state. However, the ductility of the steel does not change much as the strain cycle increases.     

The design of bus route systems — An interactive location-allocation approach

An interactive modelling approach is developed to solve the practical problem of bus route network design. Possible bus routes are identified with facilities which can be located. Zones or pairs of zones in the urban area are identified with customers who will be allocated to the established facilities. It is shown that the classical Set Covering Problem is useful under the assumption of fixed demand; the Simple Plant Location Problem is effective under the assumption of demand which is sensitive to the level of bus service provided.     

Regulatory reform and freight mode choice

Reform of trucking Vehicle Weights and Dimensions (VWD) regulations in Canada is now underway. The effect these reforms will have on the freight transportation industry are only recently the subject of research. This paper is part of this new research effort, aimed at understanding how regulatory reform in the trucking sector will affect the existing competitive relationship between trucks and the railways. The paper presents the results of study and research into modelling the relationship between mode choice and the service characteristics that are affected by VWD reform.Using several periods of data, a series of econometric models are developed which help to elucidate the relative relationships between the mode service characteristics for both of the principal interprovincial freight modes. A technique is developed and presented to model railway user costs in order to overcome the complex and often unrepresentable pricing activities of Canadian railways.The strength of the developed econometric models is presented, including their significance and statistical reliability. This is further reinforced by the similarities exhibited by all the models in the series. The selected model is applied to predict market service responses required of the railway industry in order to compete with the trucking sector now adapting to the new regulations.The impact of the newly implemented vehicle weight and dimension reform on the rail transportation industry is analyzed and railway industry improvements aimed at maintaining its market share are presented. The results predicted by the model show that railway user cost reductions should be moderate, and likely less than the level of inflation over the period of time when trucking converts its fleet to take advantage of the new regulations.Abbreviations AASHTO American Association of State Highway and Transportation Officials - CCMTA Canadian Conference of Motor Transport Administrators - EPI End products, inedible commodity classification - GVW Gross Vehicle Weight - NA 1988 VWD National Agreement - RTAC Roads and Transportation Association of Canada - VWD Vehicle Weight(s) and Dimension(s) - WA 1988 VWD Western Agreement     

Dynamics of inorganic nutrient species in the Bohai seawaters

Within the frame of a Sino-German Joint Research Program, two cruises of “R/V Dong Fang Hong 2” were carried out in September–October 1998 and April–May 1999, respectively, to understand the dynamics of nutrients in the Bohai. Nutrient species (NO₃⁻, NO₂⁻, NH₄⁺, PO₄³⁻ and SiO₃²⁻) are determined colorimetrically on board for five anchor and 30 grid stations. In situ incubation experiments are performed to determine planktonic nutrient uptake and benthic exchange flux. Nutrient concentrations display short-term variability and seasonal change in the Bohai, with higher levels in shallow coastal waters than in the Central Bohai. The influence of riverine discharge on nutrient levels can be seen from salinity isopleths, nutrient distribution and species ratios. Near-bottom (nb) waters have similar nutrient concentrations as to the surface waters in the Central Bohai, whereas stratification takes place in the Bohai Strait and North Yellow Sea. In situ incubation experiments provide evidence that the uptake ratio (i.e. N, P) by phytoplankton is proportional to the ratios among nutrient species in ambient waters. Based on the data of this study and previously publications, a preliminary estimate of nutrient budgets via riverine input and atmospheric deposition is established. The results indicate that atmospheric deposition gains importance over rivers in delivering nutrients into the Bohai and sustain the new production, following recent decrease in riverine inflow caused by drought periods in North China and damming practices. A historical review of nutrient data indicates that concentrations of nitrogen increase and phosphorus and silica decrease in the Central Bohai over last 40 years. This potentially has an important influence on the health of ecosystem in Bohai (e.g. food web and community structure), though further study is needed to examine the scenario in more detail.     

Time Gap Modeling under Mixed Traffic Condition: A Statistical Analysis

This paper attempts to model vehicular time gap, which is defined as the time interval between any two successive arrivals of vehicles at a reference point of measurement on a road segment. Such an approach is justified under the non-lane-based heterogeneous traffic conditions prevailing in developing countries such as India, characterized by many “zero” time gaps due to simultaneous arrivals within a given road width. In addition, time gap data are characterized by a significant amount of data in the tail region due to long headways. Nevertheless, many researchers of time gap modeling have used light-tailed distributions that modeled time gaps satisfactorily due to two reasons: (a) The tail data was merged into a single bin; and (b) goodness-of-fit tests such as the Chi-square test, which has many limitations, were used. Further, some researchers have suggested different distributions for the same range of traffic flows, leading to ambiguity in distribution selection. In addition, bin size, which dictates the degree of fit of any distribution, has been ascribed very less importance in time gap modeling. Hence, this paper tries to consolidate and standardize the existing research in time gap modeling research by addressing all these issues. Two new distributions, namely Generalized Pareto (GP) and Generalized Extreme Value (GEV) with better tail modeling properties, have been proposed along with other conventional distribution to model vehicular time gaps over a wide range of flow from 550 vph to 4,100 vph. Two types of goodness-of-fit tests, namely Area-based and Distance-based tests, have been used. It has been found from the study that GP distribution fits the time gap data well (overall and tails) up to a flow range of 1,500 vph based on both kinds of tests, and GEV fits the data well for the flow levels above 1,500 vph based on the area test only.     

Plate scanning tools to obtain travel times in traffic networks

The management of vehicle travel times has been shown to be fundamental to traffic network analysis. To collect travel time measurement, some methods focus solely on isolated links or highway segments, and where two measurement points, at the beginning and at the end of a section, are deemed sufficient to evaluate users' travel time. However, in many cases, transport studies involve networks in which the problem is more complex. This article takes advantage of the plate scanning technique to propose an algorithm that minimizes the required number of registering devices and their location in order to identify vehicles candidates to compute the travel times of a given set of routes (or subroutes). The merits of the proposed method are explained using simple examples and are illustrated by its application to the real network of Ciudad Real.