Rapid Prototyping and Tooling of Custom-Made Tracheobronchial Stents

Rapid prototyping (RP) and rapid tooling (RT) techniques can be applied to the field of medicine primarily because of their ability to produce customised profiles and geometries in relatively short lead times. In this paper, the process by which these techniques can be applied for the production of customised tracheobronchial stents for the purpose of maintaining patency in an occluded respiratory tract is described. A comparison of RP systems was carried out to establish the preferred RP method to produce the master model. The vacuum casting RT process was then used to produce the stent.     

重油催化裂化反应技术的新进展

近十几年来，重油催化裂化技术作为主要的重质油轻质化手段得到了迅速发展，国内外围绕催化裂化装置的提升管反应器也开发了许多新技术。综述了重油催化裂化反应技术的新进展，并对新技术的开发进行了讨论。     

稀土钕对激光快速成形TC4合金组织及性能的影响

针对氢化脱氢钛合金粉末氧含量较高的问题，研究了添加稀土钕对激光快速成形TC4合金组织及性能的影响。结果发现，添加稀土Nd后，激光快速成形TC4合金的宏观晶粒尺寸变化不大；但随稀土添加量的增加，初始β列状晶逐渐转化为全β等轴晶，晶粒内部的魏氏α组织逐渐转变为网篮α，粗化α条不断增多，呈现团束聚集趋势，晶界α集束体积分数也不断增大；随稀土添加量的增加，激光快速成形TC4合金的室温塑性先大幅度提高，然后急剧降低；稀土添加量为0．1％～0．2％（质量分数，下同）时，氧含量为0．26％的氢化脱氢TC4合金粉末激光快速成形件沉积态的抗拉强度达975MPa，延伸率9．5％，满足锻件标准要求。     

铸态及快淬态无钴AB5型贮氢合金的循环稳定性

对AB5型LaxMm1-x(NiMnSiAlFe)49(x=0,0.45,0.75,1.00,摩尔分数)贮氢合金进行了快淬处理,研究了La含量及快淬工艺对合金微观结构及电化学循环稳定性的影响.结果表明:La含量的增加对铸态合金的循环稳定性没有明显影响,但使快淬态合金的循环稳定性下降,且快淬处理能显著提高合金的循环稳定性.当La替代量从0增加到1.00时,经300次充放循环后,铸态合金的容量保持率(Rh)从59.2%增加到59.8%;16 m/s淬速快淬态合金的容量保持率从83.9%下降到65.0%.对于x=0.45的合金,当淬速从0(铸态被定义为淬速等于0)增加到28 m/s时,容量保持率从59.8%增加到75.8%.     

ELECTRON MICROANALYSIS FOR LASER MELTED ZONE IN 45 STEEL WITH Fe-Ni-Cr COATING

The Fe-Ni-Cr coating laver has been alloyed with 45 steel base metal by transverse.flow typeCO_2 gas laser of maximum output 5kW.The characteristics of the melted zone and the es-sence of the“bright band”has been investigated using the electron microscopy.The resultsshow that the“bright band”belongs to the melted zone and is a vertical section of the planecrystal,The width of the“bright band”equals the height of the plane crystal,which decreaseswith the increase of laser beam scanning rate and the decrease of laser power.This has beenexplained in terms of constitutional supercooling G/R.     

快淬工艺对无钴AB5型贮氢合金循环稳定性的影响

研究了快淬工艺对无钴AB5型LaxMm1-x(NiMnSiAlFe)4.9(x=0,0.45,0.75,1.0)合金微观结构及电化学循环稳定性的影响.结果表明快淬处理显著改善合金的成分均匀性,使晶粒细化,并显著提高合金的循环稳定性.当淬速从0m/s增加到28 m/s时,经300次充放循环后,x=0.45合金的容量衰减率D从0.28 mAh/g·c-1(c代表一次循环)下降到0.13mAh/g·c-1;x=1.0合金的容量衰减率D从0.3mAh/g·c-1下降到0.14mAh/g·c-1.     

Calculation of cooling rate of amorphous aluminum alloy melt-spun ribbons

Based on the heat transfer theory and liquid solidification theory, the heat transfer during the rapid solidification process of amorphous ribbons prepared by melt spinning was approximately modeled by one-dimensional heat conduction equation. Besides, integration with the temperature gradient, the relationship between the ribbon thickness and solidification time was derived according to the boundary conditions of ribbon-copper wheel. A simply theoretical model was obtained to calculate the cooling rates of aluminum amorphous ribbons. According to the above theoretical model, the critical cooling rate of aluminum amorphous ribbons by melt spinning is above 10^6 K/s, which proves that the aluminum based alloys belong to the marginal glass forming ability of alloys. The calculated results are in good agreement with other estimated values reported previously.     

快速低温固体S—C—N三元共渗工艺研究

以木炭、尿素和硫化铁为渗剂,用稀土化合物CeCl_3作催渗剂,于570℃进行固体S-C-N三元共渗。试验结果表明,在相同时间内加催渗剂的渗层深度比不加催渗剂的有大幅度提高,且硬度及耐磨性亦有较大提高,硬度梯度较平缓。离子探针分析表明,稀土元素Ce亦被渗入钢的表面,它不仅起到活化渗剂的作用,同时在提高钢的性能方面还起到微合金化的作用。     

Fe替代Co对AB5型贮氢合金循环稳定性的影响

用铸造及快淬的方法制备了稀土基AB5型Mm（NiMnSiAl）4．3Co0.6-xFex（x=0，0．1，0．2，0．3，0．4，0．5，0．6）贮氢合金，用XRD。TEM及SEM观测了铸态及快淬态的微观结构，测试了合金在铸态及快淬态下的电化学循环稳定性。研究了Fe替代Co对铸态及快淬态贮氢合金微观结构及循环稳定性的影响。研究结果表明，Fe替代Co对铸态及快淬态合金的相结构没有明显影响，但对合金的循环稳定性产生显著影响。Fe替代Co能不同程度地改善铸态及快淬态合金的循环稳定性，但对快淬态合金循环寿命的改善更加显著，导致这一结果的主要原因是Fe替代Co使快淬态合金的微观组织显著细化。