Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

高层地下室底板混凝土施工的裂缝控制

以德益花园写字公寓楼地下室底板205m厚混凝土的施工工程为例，坚持预防为主的原则，采取了一系列温控技术措施，有效地防止或控制了温度裂缝(收缩裂缝)的产生，确保了混凝土的施工质量。     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

高温和低张应力引起的非平衡晶界偏聚动力学(Ⅱ)--实验结果的动力学模拟

以文献[1]建立的张应力引起的非平衡晶界偏聚动力学方程模拟了Shinoda T等的磷在钢中的应力时效实验结果和Misra R D K的硫在钢中的应力时效实验结果，模拟结果与实验结果互相吻合。通过模拟发现，张应力使磷-空位复合体以及硫-空位复合体在钢中的扩散系数均增加3个数量级，且磷原子和硫原子的扩散系数分别降低3个和5个数量级。     

有序聚类法在锦凌水库风化岩体定量分带中的应用

应用有序聚类法对辽宁省锦凌水库坝基的风化岩体进行定量分带,所得结果与地质观察方法、规范法等所得出的结果进行了分析比较.采用岩体风化差异系数法进行综合分析,最终推荐按照有序聚类方法进行风化岩体分带.     

高温季节大体积混凝土基础施工的裂缝控制

文章以上海富华大厦工程为例,对在高温季节如何针对大体积混凝土基础施工的裂缝进行控制,提出了相关措施,达到了控制裂缝的预期目标。     

潮湿扩散及湿热应力对叠层封装件可靠性影响

利用MARC软件,通过模拟实验分析了潮湿扩散及湿热应力对叠层封装器件可靠性的影响,对30℃,RH 60%,192 h条件下预置吸潮到后面的无铅回流焊解吸潮过程进行了有限元仿真;对85℃,RH 85%,168 h条件下元件内不同界面的潮湿扩散进行分析,得出潮湿扩散对界面的影响规律。使用一种湿热耦合方法计算湿热合成应力并与单纯热应力进行了对比。结果表明:最大湿热应力和热应力一样总是出现在顶部芯片与隔离片相交的区域,其数值是单纯热应力数值的1.3~1.5倍。     

某铁路医院加速器室大体积防射线混凝土施工

结合大同铁路分局中心医院直线加速器室工程实际，介绍了大体积防射线混凝土的特点及施工中应注意的事项，并阐述了具体的施工技术。     

常压渣油热反应过程中胶体的稳定性

利用质量分数电导率方法研究了中东和克拉玛依常压渣油在热反应过程中胶体的稳定性。结果表明，随着反应时间的增长，在热反应生焦诱导期内，渣油的胶体稳定性迅速下降；开始生焦后，胶体稳定性缓慢下降。从中东常压渣油的SARA四组分的数均相对分子质量、碳氢元素组成、平均芳碳率等方面探讨了中东常压渣油在热反应过程中胶体稳定性下降的原因。结果表明，在热反应中，由于裂解和缩聚反应的共同作用，使渣油的沥青质和饱和分含量上升，芳香分含量下降，胶质含量变化不大；随着热反应的进行，四组分的数均相对分子质量均呈下降趋势，导致了渣油胶体稳定性的下降并发生生焦反应。