三峡三期工程主坝大体积混凝土内部温度控制

三峡右岸三期工程施工中,为了有效控制坝体大体积混凝土内部温升,采取了高温季节使用预冷混凝土浇筑、控制混凝土出机口温度及浇筑温度、对混凝土内部人工通水进行初冷、中冷和后冷等措施。三峡三期工程大坝混凝土内部温度没有出现超标现象,混凝土温控工作取得了良好的效果。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

无限水域中孤立悬臂板的自由振动

本文内容包括：（１）把求解无限小域中孤立悬臂板的振动问题转化为求解水体对板振动的影响，给出了本征值与本征函数摄动量的表达式；（２）利用一个特殊变换求解了规定条件下的附加质量；（３）给出了非淹没板在不计及水面波动时正对称第一、二自振频率的计算结果。     

MPID─TOF质谱的快速时间分辨微弱信号测试系统

把瞬态记录仪Ｂｉｏｍａｔｉｏｎ８ｌ００与微型计算机ＩＢＭ─ｐＣ／ＸＴ联接建成了一个高速数据采集系统，本文介绍了系统的硬件接口设计及软件设计。在超声分子束条件下，把它应用于环氧乙烷（Ｃ＿２Ｈ＿４Ｏ）的多光子电离与离解飞行时间（ＭＰＩＤ─ＴＯＦ）质谱的实验研究中，并给出了实验结果；本系统在微观基元化学反应动力学实验研究中广泛适用于对时间分辨微弱信号的探测。     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

气体引射器流体动力特性实验研究

在实验装置上对气体引射器计算基本公式进行了实测验证，分析了理论特性曲线的可信度。通过实验，获得一些参数对引射器工况的影响规律。     

面向大批量定制生产的产品族设计技术综述

随着市场竞争的日益激烈,传统的大批量生产和单一的定制生产模式在激烈的市场竞争中已失去竞争优势,大批量定制生产模式,已成为制造业发展的必然趋势,它试图将大批量生产的高效率、低成本与定制生产灵活性、个性化的优势结合起来。开展产品族设计是实现大批量定制生产的有效途径。论述了大批量定制生产与产品族设计的关系,并对国内外有关产品族设计的文献进行了系统的整理和归类,提出了产品族设计系统框架,且对产品族设计的实现方法进行了介绍。     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

CMF300M355NU型质量流量计在油库汽车装车中的应用

介绍了质量流量计的工作原理有应用效果。这种新型质量流量计精度高，稳定性好，示值计量简便，可直接显示质量、流量、介质温度、密度等，维护量低，但必须正确安装、使用，才能发挥其应有的作用。     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.