Best L1 Piecewise Monotonic Data Modelling

Let us consider n data measurements of a univariate process that have been altered by random errors. We assume that an underlying model function has a substantially smaller number of turning points than the observed ones. We propose algorithms that make least the sum of the moduli of the errors by requiring k monotonic sections, alternately increasing and decreasing, in the sequence of the smoothed values. The main difficulty in this calculation is that the optimal positions of the joins of the monotonic sections have to be found automatically among so many combinations that it is impossible to test each one separately. Moreover, the calculation seems to be very intractable to general optimization techniques because O(n^k) local minima can occur. It is shown that dynamic programming can be used for separating the data into optimal disjoint sections of adjacent data, where each section requires a single L₁ monotonic calculation. This procedure is highly efficient, requiring at most O(kn²) computer operations and O(n) best L₁ monotonic calculations to subranges of data for a global minimum.     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

潜油电动机滑行时间的自动测量

潜油电动机滑行时间是评定电动机装配质量的重要指标。鉴于手工测量电动机滑行时间存在效率低和误差较大的不足,设计了潜油电动机滑行时间自动测量系统。它通过分压电路和计算机自动测量系统测量潜油电动机定子上感应的电压变化状况,即可得到电动机滑行时间。用手工测量、波形分析和自动测量3种方法测量6种型号电动机的滑行时间,其中5种滑行时间长于3s,判定为合格;1种滑行时间短于3s,判定为不合格。3种方式测量的滑行时间具有较好的一致性,仅波形分析法得出的滑行时间比自动测量的滑行时间稍长,表明自动测量方法的精度和重复性可满足要求。     

Material state remapping in computational solid mechanics

A computational procedure for remapping material state information from one finite element mesh to another is described. The procedure is useful in connection with evolving meshes for inelastic problems, as for example occur in the context of fracture simulation and adaptive mesh refinement. The proposed method is based on weak enforcement of equality between corresponding fields on the two meshes, where piecewise‐constant fields on both meshes are generalized from the quadrature‐point values. The essential algorithmic problem is that of calculating the volume partition of an arbitrary convex region with respect to a covering set of disjoint convex regions. Instead of geometrically resolving the associated intersections, the problem is herein approximated by a constrained optimization problem, which may be readily and efficiently solved computationally. This formulation is a main contribution of the paper. Computational examples are given that illustrate the effectiveness of the proposed procedure. Copyright © 2002 John Wiley & Sons, Ltd.     

外转子电机关键技术及解决措施

对外转子电机的关键技术和主要工艺问题进行了探讨分析，并提出了解决措施。     

合成直链烷基苯环境友好固体酸催化剂的研究 Ⅲ .催化剂失活原因分析

采用固定床反应器,对催化剂的稳定性进行了初步评价。在120℃、空速相同、液固反应条件下,高苯烯比时催化剂的稳定性明显高于低苯烯比时;在苯烯比和空速相同、液固反应条件下,相对低温反应时,催化剂的稳定性明显高于高温反应。IR分析结果表明,同新鲜和反应后未失活的催化剂相比,失活后催化剂的活性组分特征衍射峰消失,出现的新的特征衍射峰可能同—CH基的振动有关。TG分析结果表明,失活后催化剂在空气流中焙烧,失重幅度比新鲜催化剂大。     

中压电动机传统起动方式的危害性

本通过对中压电动机的几种传统起动方式的探讨分析，阐述了使用这些方法对电网和周围其他用电设备产生的不利影响，提出了改进措施。