生物降解型聚碳酸顺丁烯二酸亚乙酯 1、合成和表征

用CO_2、环氧乙烷、顺丁烯二酸酐进行三元共聚首次得到聚碳酸顺丁烯二酸亚乙酯(PECM),并用IR、~1H NMR、DSC等进行了表征,共聚物链中CO_2和MA单元随机分布,不饱和单元可在0～0.5mol分数之间调节。共聚过程不发生双键交联和构型转化。环氧乙烷的转化率可高达到93％。控制PECM链上的双键含量并使之发生自由基加成反应,得到对热较稳定的可溶性产物。     

A theory for the formation of tetrahedral amorphous carbon including deposition rate effects

A theoretical model is presented to describe the effect of ion beam bombardment rate on the formation of tetrahedral amorphous carbon (ta-C) films. The critical ion energy, E_c, corresponding to a 50% sp³ content in the films, is found to be dependent on both the effective thermal resistance and the ion beam bombardment rate. In the model, the ‘window’ width in the ion energy scale for the formation of ta-C material increases with decreasing deposition rate and with a reduction in the effective thermal resistance, until limited by lower and upper boundary thresholds. Experimental data are reproduced by the model. The plasmon energy, which correlates with sp³ fraction, is found experimentally of be higher for lower deposition rate and smaller effective thermal resistance. Data points for high sp³ content ta-C films deposited on silicon substrates at room temperature occupy a region in the ion energy-deposition rate (E-r) diagram similar to that predicated from the theory.     

镀Cu碳毡／环氧树脂复合的研制

研究了镀Ｃｕ碳毡／环氧树脂（ＣｕＣＦ／ＥＰ）复合材料的制备，并探讨了镀Ｃｕ量对碳毡电阻率，复合材料电阻率及其电磁屏蔽效率的影响规律，经合理工艺制得的镀Ｃｕ碳毡（４００ｍｇ．ｇ＾－１Ｃｕ－ＣＦ）含量为３００ｍｇ．ｇ＾－１ＣｕＣＦ／ＥＰ复合材料，其电磁屏蔽效率可在２０＝－１０００ＭＨＺ范围内达到６０ｄＢ。     

低速爆轰管对黑火药的点传火性能研究

文章采用中心点火管结构的实验装置研究了黑火药的点传火性能。用低速爆轰 (L VD)中心点火管来点燃黑火药时 ,1# ～ 3# 大粒黑药的传火速度为 70 0 m· s-1～ 80 0 m· s-1数量级 ,燃烧波宽度在 3.1ms～ 3.5 ms,最大压力峰值 :1# 为 36 .4 MPa,2 # 为 2 4 .0 MPa,3# 为 38.0 MPa。用普通中心点火管点燃黑火药时 ,2 # 、3# 和钝化 2 # 大粒黑的传火速度分别为 6 1.2 m· s-1、6 8.2 m·s-1和 4 0 .1m· s-1,最大燃烧波宽度分别为 9.2 ms、6 .3ms和 9.5 ms。燃烧波表明 ,L VD中心传火管与普通中心传火管相比较 ,在传火管的不同位置处 ,前者的 P- t曲线一致性远高于后者。     

交联剂在碳／碳复合材料沥青基体中的作用

本文从C/C复合合材料的基体入手，分析了交联剂在沥青中的交联机理，并以此为基础对中温煤沥青在催化剂作用下进行交联反应。结果表明，交联剂在C/C复合材料基体中的交联作用非常明显，不仅基体本身的残碳率及耐热程度有很大提高，而且，以它制成的C/C复合材料的抗压强度也有显著增加。     

Carbon fibre cloth as an electrode material: electrical conductivity and mass transfer

The paper deals with carbon fibre cloth electrodes, employed in the fabrication of composite materials. The electrical conductivity of single bundles, groups of bundles and cloth is studied. Ohm's law applies to the electrical conduction in the direction of the fibre length, but bundle conductivity decreases with the number of fibres in the bundle. Electrochemical mass transfer between a flowing electrolyte and a cloth arranged as a flow-through or a flow-by porous electrode indicates the existence of double porosity in the material. Due to double porosity, only the external surface of the cloth works as an electrode. This finding shows that the material is not suitable for such an application.     

Evolution of BET internal surface area in glassy carbon powder during thermal oxidation

It is demonstrated that glassy carbon powder can be thermochemically activated. During activation, a film with open pores is created on the glassy carbon particles. This film has a large internal surface area, which is accessible to liquids and gases. A simple model for the evolution of the internal surface area in glassy carbon powder during thermochemical gas-phase oxidation is also presented and compared with experimental data. Experimental results are in qualitative agreement with the model. We found that a sharp particle size distribution is desirable with regard to potential technical applications.     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

低浓度CO合成甲酸甲酯中试研究

进行了低浓度CO合成甲酸甲酯的中试研究,探讨了温度、压力、流速、催化剂浓度等因素对反应的影响,在优化条件下考察了系统的稳定性。结果表明,低浓度CO(体积分数15%)合成甲酸甲酯CO的单程转化率达到50%以上,粗品中甲酸甲酯含量达到7%～9%,可以满足工业浓缩要求,且整个合成系统未发生母液堵塞的问题,与高浓度CO羰基合成甲酸甲酯相比,单位生产成本可降低30%,具有良好的技术先进性。     

炭/炭复合材料抗氧化涂层厚度的光学测量

选用A,B,C,D4种炭/炭复合材料试样进行抗氧化涂层厚度的光学测量研究。其中:试样A,B孔隙度相同,均为15.85％,对其涂覆粒径分别为1μm和10μm的B_4C涂层;试样C,D孔隙度分别为13.52％和16.78％,对其均涂覆粒径为10μm的B_4C涂层。然后通过金相光学测量其涂层厚度,在抗氧化涂层厚度的计算过程中,对试样组织的内部未渗入抗氧化涂层的孔隙进行图像处理。结果表明:当试样孔隙度相同时,涂层材料粒径越小,其涂层越厚;当抗氧化涂层材料粒径相同时,试样孔隙度越大,涂层越厚。