Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.     

Off-Site Exposure to Respirable Aerosols Produced during the Disk-Incorporation of Class B Biosolids

Field experiments were conducted at a Class B biosolids land application site in central Arizona to measure, model, and source-track the off-site transport of aerosols emitted when biosolids were disk-incorporated into soils. Real-time PM10 monitoring provided time-resolved aerosol information sufficient for verifying both off-site concentration and off-site exposure time model results. Under the conditions considered and at a distance of 165?m from the aerosol source, biosolids disk-incorporation resulted in an intermittent exposure to biosolids-derived aerosol concentration between 15 and 40?μg/m3 and an inhalable biosolids dose between 2 and 8?μg. Transport modeling predicted that these doses will decrease with increasing wind speed. In addition, three DNA sequence-based biosolids source tracking methods were applied to aerosol samples and confirmed the presence of biosolids in aerosols at 5, 65, and 165?m from the aerosol source. Field measurements and modeling indicate that the nature of biosolids-derived aerosol exposure is a series of intermittent high concentration puffs, rather than a continuous low concentration.     

The complexity of economic equilibria for house allocation markets

We prove NP-completeness of deciding the existence of an economic equilibrium in so-called house allocation markets. House allocation markets are markets with indivisible goods in which every agent holds exactly one copy of some good.     

Identification of gaps in mangrove forests with airborne LIDAR

Mangrove forests change frequently due to disturbances from tropical storms, frost, lightning, and insects. It has been suggested that the death and regeneration of trees in small gaps due to lightning may play a critical role in mangrove forest turnover; however, the large-scale quantification of spatial pattern and areas of gaps is lacking for investigating this issue. Airborne light detection and ranging (LIDAR) technology provides an effective way for identifying gaps by remotely obtaining direct measurements of ground and canopy elevations. A method based on an alternative sequential filter and black top-hat mathematical morphological transformation was developed to extract gap features. Comparison of identified gap polygons with raw LIDAR measurements and field surveys shows that the proposed method successfully extracted gap features in mangrove forests in Everglades National Park. There are 400–500 lightning gaps per square kilometer in mangrove forests at the study sites. The distribution of gap sizes follows an exponential form and the area of gaps with sizes larger than 100 m² account for 55–61% of the total area of gaps. The area of gaps in the mangrove forest in Everglades National Park is about 4–5% of the total forest area and the average gap formation rate is about 0.3% of the total forest area per year, indicating that lightning gaps play an important role in mangrove forest dynamics.     

多孔挡板流化床还原UO3反应器模型的研究

针对ＵＯ＿３的Ｎ＿２还原反应建立了多孔挡板流化床反应器模型。将多孔挡板床的每一级视为具有相似的流动状态，每一级的上、下段称为稀、密相段，分别用鼓泡床和活塞流模型描述。该模型的计算值与￠６３ｍｍ的多孔挡板床Ｈ＿２还原ＵＯ＿３的热态实验值能较好的吻合。还预计了还原温度、操作气速和挡板结构参数对固相转化率的影响，为该类反应器的工业设计、放大和优化提供了依据。     

用数理统计方法判定检测下限

该文介绍如何用数理统计方法判定检测下限。     

Evaluation of Morphology—Stable Critical Size of KNbO3 Crystals

Skeletal form of KnbO3 crystals growing in Li2B4O7 solvent was in-situ observed at 900℃ and it was found that shallow depression started to develop on the surface of KnbO3 crystals when the crystal size exceeded several micron,typically 7 micron.Based on the quantitative criterion derived by Chernov,the estimated critical size of KNbO3 crystals was 1 micron,which was consistent with the experimental measurement.The kinetic coefficients,Kcorner and Kcr,in the criterion were experimentally obtained in the diffusive-convective and diffusive-advective flow states respectively.     

Mathematical modelling of a reverse flow reactor with catalytic surface dynamics

This paper studies a system of partial differential equations modelling the behaviour of a reverse flow reactor. For the parameters appropriate for the oxidation of ammonia on a Pt/Al₂O₃ catalyst in a typical laboratory set-up, the reactor may be split into regions where approximate formulas that determine its behaviour are deduced. Numerical calculations are presented and can be used to compare with the analytical formulas. The physical insight gained from the asymptotic analysis suggests a new switching strategy which is the subject of numerical experiments. The switching strategy is found to be efficient at minimising the ammonia exiting the reactor after reversal.