几种酚类抗氧剂在润滑油中的应用

采用旋转氧弹法、高压差示扫描量热法等方法研究了5种酚类抗氧剂对6种润滑油基础油氧化安定性的改善效果。结果表明:向加氢基础油中加入0.25%(质量分数)抗氧剂2246-S和RHY510(含硫酚类抗氧剂),可使HVIWH125,HVIWH150,HVIWH500,KN4006,KN40105种润滑油基础油的诱导期由27～88min提高到226～397min;使HVIWH125,HVIWH150,HVIWH300,HVIWH500,KN4006,KN40106种润滑油基础油的起始氧化温度由193.34～198.90℃提高到205.48～230.27℃。     

化学-电解氧化法制备高铁酸钾的研究

本文用化学－电解氧化法制备高铁酸钾，克服了纯化学氧化法产品需要提纯和纯电解氧化法制备周期长的缺点，得到了高纯度的高铁酸钾晶体。     

FCC汽油光催化氧化脱硫的实验室研究

采用光催化氧化与液液萃取同时进行的方法，考察了光敏剂十六烷基三甲基溴化铵的用量、pH值、双氧水体积分数和反应时间对脱硫效果的影响。结果表明，在光源为主波长365nm的300W中压汞灯，双氧水体积分数为25％，FCC汽油与双氧水体积比为1：3，总体积为120mL，加入0．20g十六烷基三甲基溴化铵，以7000r／min高速均质5min，pH值为4，光照10h的实验条件下，FCC汽油脱硫率可达91．20％；脱硫后的双氧水及光敏剂可以重复使用，不会造成二次污染。     

炼油厂碱性污水生物催化氧化预处理工艺研究

在对炼油厂碱性污水水质分析的基础上,提出采用生物催化氧化工艺对碱性污水进行预处理。试验结果表明,在水力停留时间为4 h,曝气量(标准状态)为8 m3／h的条件下,碱性污水的硫化物去除率可达90％以上,出水中的硫化物平均值为15．2 mg/L,CODCR、酚和油的去除率分别为47．5％,44．1％,50．8％,其中CODCR体积负荷为3．85 kg／(m3·d),是传统生化处理的10倍, 达到了污水预处理的目的。     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

催化裂化汽油光化学氧化脱硫

以水为萃取剂、空气中的O2为氧化剂、500W高压汞灯为紫外光光源,研究了催化裂化(FCC)汽油光化学氧化反应的机理和氧化产物,考察了反应条件对FCC汽油脱硫率的影响。实验结果表明,FCC汽油中的极性含硫化合物首先部分溶于水相中,然后在水相中被氧化。在空气通入量为150mL/min、水与FCC汽油的体积比为1.0的条件下,反应5h后FCC汽油脱硫率达40.6%,加入0.45g4A分子筛作为O2的吸附剂后FCC汽油脱硫率提高到70.2%。FCC汽油的光化学氧化反应为一级动力学反应,加入4A分子筛时的反应速率常数为0.217 4h-1,半衰期为3.18h。FCC汽油光化学氧化反应的主要产物为亚砜和砜,并进一步生成CO2、草酸、SO24-等。     

橡胶促进剂DM的合成工艺

M氧化生成DM是自由基反应机理，结合微反应器机理，采用分子氧化的反应方式，选用绿色溶剂异丙醇、环境友好型氧化剂H202，一步法制取高品质DM。对反应时间、反应温度、氧化剂用量等因素进行考察，确定最佳工艺条件为：反应时间90min，反应温度55℃，氧化剂不过量，碱过量5％，M—Na溶液M含量30％，加料时N60 min，溶剂用量为M—Na溶液质量的1．5倍，所得产品质量合格，熔点可达180℃。     

Methane oxidation over vanadium-modified Pd/Al2O3 catalysts

Three different vanadium-modified Pd/Al₂O₃ catalysts were prepared and tested as catalysts for the deep oxidation of methane. Vanadium was added to the palladium catalyst by incipient wetness of palladium catalyst in order to modify its properties and improve its thermal stability and thioresistance. The behaviour of vanadium-modified catalysts depends on the concentration of this compound, being 0.5 wt.% the optimum amount. However, when strong catalyst poisons are present in the gas (SO₂), these modified catalysts do not show a better performance than unmodified catalyst. Bimetallic catalysts were tested with and without further reduction, being observed that reduced bimetallic catalysts perform worse than the non-reduced ones.     

CeO2对RuO2／γ-A12O3催化剂湿式氧化降解苯酚性能的影响

采用浸渍法制备了RuO2／γ-A12O3和RuO2／CeO2／γ-A12O3催化剂，并利用XRD、SEM和XPS对催化剂进行了表征，研究了Ce的加入对RuO2／γ-A12O3催化剂表面分散性和催化剂表面元素Ru，O和Ce化学态的影响，同时考察了RuO2／γ-A12O3和RuO2／CeO2／γ-A12O3催化剂湿式氧化降解苯酚的活性，并深入探讨了Ce对RuO2／γ-A12O3催化剂的助催化作用。结果表明：Ce掺杂改性后，使催化剂表面Ru的化学态降低、表面氧空位增加，并且活性组分Ru的分散性增加，从而使RuO2／CeO2／γ-A12O3催化剂的活性提高，因此Ce起到了显著的助催化作用。     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.