Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

粉末冶金法制备PSZ/Mo复合材料的研究

本文采用粉末冶金法制备了不同成分的PSZ/Mo复合材料。并对其密度、弹性模量和热膨胀系数进行了测量和分析 ,用XRD进行了物相分析。实验结果表明 :纳米氧化锆的烧结性能比金属钼好 ;弹性模量估算选用简单混合法则进行计算时应进行修正 ;钼和氧化锆在烧结时不发生化学反应。通过热压PSZ/Mo功能梯度材料的断口扫描分析发现 :虽然金属钼和纳米氧化锆具有一定增韧作用 ,但材料断裂方式仍以脆性断裂为主     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

Preparation and Application of Active Composite Antibacterial Material Containing Ag~ and Zn~(2 )

1Introduction Harmfulbacteriaexistanywhereintheworldsuchas soil,air,water,surfacesofobjectsandourskins,etc.Thenumberofbacteriumisenormous,withmanydiffer entspecies.Theyhavethreatenedthehealthofhuman beingsseriously.Withthedevelopmentofeconomyand environme…     

Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

复合绝缘子老化评估方法浅析

复合绝缘子老化是用户十分关心的问题。笔者介绍了两种判别复合绝缘子老化程度的方法,并通过实例,分析了这两种方法的优点以及存在的问题。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

Corrosion Inhibition Mechanism with Spilt Cell Technique of Rare Earth Metal on LC4 Al Alloy

A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl₃, the influence of corrosive performance of CeCl₃ on LC4 super-power aluminum alloy in the 0.1 mol·L⁻¹ NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl₃ solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.     

In situ formation of multi scale reinforcing phases to improve performance of Al2O3-SiC C castables

In order to improve the physical properties and slag corrosion resistance of refractory materials for hot metal pretreatment, different contents of composite metal powders (CMP) were introduced into Al2O3-SiC-C refractory castables. The effect of CMP on the microstructure, physical properties and slag corrosion resistance of Al2O3-SiC-C refractory castables were studied. The results show that the multi scale reinforcing phases including flake crystals, rod shaped fibers, filamentous fibers and whiskers are in situ formed in the samples with addition of CMP, which result to the improvement of the cold modulus of rupture and cold crushing strength. When the addition of CMP is 6 wt.%, the high temperature modulus of rupture increases by 231%, the thermal shock resistance increases by 77% after thermal shock by water cooling 5 times and the percentage of the slag resistant area reduces by 37.2%.