Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

LD钢超塑性压缩变形参数与金相组织

通过对ＬＤ（７Ｃｒ７Ｍｏ３Ｖ２Ｓｉ）模具钢起塑性压缩变形后的金相组织观察研究，分析了变形参数、原始组织对变形后金相组织的影响。     

双塔脱丙烷工艺技术

对扬子乙烯装置双塔脱丙烷系统低压塔液泛、高压塔再沸器堵塞等问题进行了技术分析,提出了工艺流程修改方案,完善了双塔脱丙烷技术,对同类装置有参考价值。     

濮城油田东西区沙二下顶面微构造特征与剩余油分布

濮城油田沙二下是一个被断层复杂化了的断块型油气藏，通过对储层的精细描述表明，各砂岩组顶面微构造发育，其成因有2种，与构造作用有关的微构造及与构造作用无关的微构造，前者规模较大，后者规模通常较小，根据微构造的起伏变化和形态，可分为3类：正向微构造，负向微构造，斜面微构造，正向微构造是油气富集与控制剩余油分布的重要微构造。     

半固态ZnAl 27合金及其二次加热组织

研究了半固态ZnAl27合金及其二次加热组织。结果表明，半固态ZnAl27合金基本无宏观偏析，其组织为细小均匀的近球形非枝晶，综合力学性能远远高于常规铸造合金；二次加热后，α相进一步球化，边缘变得光滑圆整，可以满足半固态触变成形的需要。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

Yield Stress and Microstructure of Set Yogurt Made from High Hydrostatic Pressure-Treated Full Fat Milk

ABSTRACT: Set yogurts were prepared from fortified milk subjected to the following processes: (a) Thermal process (85C,°C,35 min), (b) High hydrostatic pressure process (193 or 676 MPa for 5 or 30 min), and (c) Nonprocessed milk (control). Yogurts from milk treated with 676 MPa for 30 min exhibited similar yield stress and water-holding capacity (WHC) to yogurts from heated milk. Transmission Electron Microscopy (TEM) micrographs exhibited small round casein micelle aggregates without appendages in yogurts from heated milk. Yogurts from milk treated with 193 MPa and untreated milk exhibited low yield stress, low WHC, and large clusters of coalesced micelles. Mechanisms for gel formation are discussed.     

NiTi形状记忆薄膜的显微结构和力学性能

NiTi形状记忆合金薄膜具有形状记忆效应，极有希望用于制造高技术领域微电子机械系统中的微型激发器。NiTi形状记忆合金薄膜在制备和使用过程中需要高品质（衬）底材。本文利用高分辨电子显微学和高分辨分析电子显微学详细研究了硅底材NiTi形状记忆合金薄膜的NiTi／Si和NiTi／SiO2微结构体系，包括薄膜精细结构和界面反应。也研究了其显微结构和力学性能的关系。特别给出了NiTi形状记忆合金薄膜产生疲劳过程的微观过程的起因，通过高达十万个使用热循环前后样品显微结构变化的比较，发现纳米尺度上的TiNi3新相的形成导致疲劳过程的发生。如何抑制TiNi3新相形成的研究正在进行之中，这将为进一步提高NiTi形状记忆合金的使用寿命指出方向。