PEG20000中试放大的工艺研究

在一定温度和催化剂作用下 ,分别利用本体聚合和溶剂聚合的方法 ,在 1L、10 0L不锈钢高压反应釜中合成了相对分子质量为 2 0 0 0 0的聚乙二醇 ,并讨论了聚合反应机理 ,研究了催化剂用量、反应温度、反应时间对聚合反应的影响。经过红外、核磁共振、凝胶色谱、化学分析等方法对产物进行了表征。     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Hydrogen production in solid electrolyte membrane reactors (SEMRs)

In the present work, the prospects and trends of solid electrolyte membrane reactors (SEMRs) towards hydrogen production, are discussed. Initially, an overview of the principles, the properties and the techniques related to the usage of the SEMRs, are presented. In the following, a literature survey covering earlier and recent developments of the various methods (e.g. reforming or partial oxidation or dehydrogenation of hydrocarbons, steam electrolysis) employed in the SEMRs for the production of hydrogen, is performed. Finally, the current status of this research field is analyzed and future research topics are proposed.     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

Preparation of CeO2-ZrO2 mixed oxide with high surface area and high thermal stability

Ceria-zirconia solid particles have been recognized as a key material of the automotive exhaust catalysts since they can release and uptake oxygen owing to the rapid reversible oxidation states of cerium between Ce³⁺ and Ce⁴⁺. Several methods have recently been described to prepare the CeO₂-ZrO₂ solid particles used in the catalysts. In this paper, a new coprecipitation method is used to prepare the CeO₂-ZrO₂ solid particles. The Ce-Zr alcogel is dried and calcined in flowing N₂ not in flowing air under atmospheric pressure. The results show that the ceria-zirconia sample calcined at 650 °C has high surface area over 90 m²g⁻¹, which drops to 40 m²g⁻¹ following treatment at 900°C.     

化学还原法制备纳米铜粉的研究

本文采用KBH4在液相中化学还原CuSO4,并加入KOH和络合剂EDTA ,制得了纳米级的纯净的铜粉 ,通过调整反应物的浓度 ,可以消除Cu2 O等杂质。制备的纳米铜粉还存在一定程度的团聚 ,需试验加入分散剂来改善。     

求非线性方程近似解的逐次迭代法

本文提出了求解非线性问题的一种新方法——逐次迭代法，本方法先是给出一个初始近似解，然后将这个近似解进行校正迭代，使之接近于真实解，把一个非线性问题转化为一个线性问题来解决。     

PVDF中空纤维滤膜的形态结构

用Ｌ－Ｓ相转换法制备了聚偏氟乙烯（ＰＶＤＦ）中空纤维不对称滤膜。铸膜液由聚合物、溶剂和添加剂组成。用电子显微镜（ＳＥＭ）考察了聚合物浓度、添加剂用量及种类对膜形态结构的影响。实验结果表明，聚合物浓度对膜形态结构有显著影响，当铸膜液中聚合物浓度较低时，无论用什么种类添加剂，都能形成大、且多的孔，但孔的形状随添加剂不同而异。当恒定聚合物浓度时，添加剂的用量对膜形态结构有很大的影响，但孔的大小及多少与添加剂含量的多少不成正比。     

Analytical Calculation of Large-Scale Deflection of Pulse-Loaded Elliptic Plates

Large deflections of pulse-loaded elliptic and round plates made of hardenable elastoplastic materials are investigated analytically using an energy-based approach. Formulas that are convenient for engineering design have been derived.     

Morphology and structure of poly(p-phenylene terephthalamide) crystallized from dilute organic solution

The high-temperature crystallization of poly(p-phenylene terephthalamide) (PPTA) from dilute organic solutions was achieved through the introduction of a non-solvent, or precipitating agent, at the desired crystallization temperature. The morphology and crystal structure were examined for crystals produced from PPTA polymer with two different molecular weights (M_w = 46000 and 3430 g mol⁻¹), using transmission electron microscopy. For the high-molecular-weight polymer, ribbon-like crystals were produced, while the low-molecular-weight polymer yielded small needles or platelets. In both cases, electron diffraction showed that the Northolt allomorph was obtained. For the high-molecular-weight polymer, the molecular axes were parallel to the ribbon axes in a chain-extended type structure. A hypothesis for the orientation of the low-molecular-weight PPTA in the small platelets, is also given.