Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

Y-Ba-Cu-O超导涂层的研制

用等离子喷涂工艺制备了 Y-Ba-Cu-O 高临界温度超导涂层,涂层的初始转变温度为101K、零电阻温度为86K。电阻率与磁化率的测量结果表明这种超导涂层具有与烧结超导块体相类似的性能,X 光衍射谱显示出涂层主要由 YBa_2Cu_3O_(?)单相化合物组成。     

丙烯酸树脂涂料的近期进展

介绍了丙烯酸树脂涂料的国内外发展的概况及其性能和应用.提出了我国发展丙烯酸树脂涂料的建议。     

含氚废水水泥固化实验研究

研究用水泥固化处理氚废水,并选择了最佳配方:水与灰的重量比=0.45～0.5,水泥与石膏重量比=5∶1。用IAEA推荐的方法做浸出实验。为了减少水泥固化体中氚的浸出量,实验了几种涂层材料。沥青涂层可将固化体氚的浸出率降低1～2个量级。     

Deformation analysis of skew ruled surface shells by moiré interference

The use of thin film grids coated on surfaces is described in relation to the determination of deformations in doubly curved shells. The technique is called the coating film moiré interference method and employs a laser holographic approach.     

镀锌测厚仪

本文叙述了Ｘ射线荧光测厚仪的原理、特点及测量头的设计考虑原则。并以我们研制的两种镀锌测得仪为例作了详细说明。     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

二硅化钼用于钼基的耐热涂层

介绍ＭｏＳｉＯ２用于钼基的耐热涂层，进行涂层的动力、金相学和添加剂的分析。     

Monte Carlo simulations to determine coating uniformity in a Wurster fluidized bed coating process

This paper presents a coating model to predict the mass coating uniformity in a Wurster fluid bed coater using a Monte Carlo method. The velocity and voidage data obtained using imaging techniques on the same Wurster coater are used as inputs to the model. The semi-circular Wurster fluid bed used in this work was 22.9 cm in diameter. A batch of 3.6 kg tablets was used to conduct coating experiments and the coating weight gain distribution results were compared to predictions from the simulation. The model rigorously considers the sheltering effect of particles as they move in the spray zone. Good agreement was obtained when comparing the results with an analytical model.Spray shape and orientation of discretization were found to play an important role in predicting the coating uniformity. A simple spray experiment in a particle-free bed showed that the direction of spray material, in general, was vertically upward. Simulation results confirmed that an upward cylindrical spray model gives better agreement with experimental results compared to a solid cone spray model. Finally, the model was used to predict the changes in coating uniformity with bed operating conditions such as gas velocity and gap height. A wider coating distribution was found for the case with the lower gas velocity and gap height.     

Co^3＋—modified Surface of LiMn2O4 Spinel for its Improvementof Electrochemical Properties

Cobalt was used to modify the surface of spinel LiMn2O4 by a solution technique to produce Co^3 -modified surface material (COMSM). Cobalt was only doped into the surface of LiMn2O4 spinel. XPS(X-ray photoelectron spectroscopy) analysis confirms the valence state of Co^3 . COMSM has stable spinel structure and can prevent active materials from the corrosion of electrolyte. The ICP(inductively coupled plasma) determination of the spinel dissolution in electrolyte showed the content of Mn dissolved from COMSM was smaller than that from the pure spinel. AC impedance patterns show that the charge-transfer resistance (Rct) for COMSM is smaller than that for pure spinel. The particles of COMSM are bigger in size than those of pure spinel according to the micrographs of SEM(scanning electron microscopy). The determinations of the electrochemical characterization show that COMSM has both good cycling performance and high initial capacity of 124.1 mA/h at an average capacity loss of 0.19 mAh/g per cycle.