Matrix mediated alignment of single wall carbon nanotubes in polymer composite films

Alignment of single wall carbon nanotubes (SWNT) in liquid crystalline (LC) polymer matrix imparting orientation to the nanotubes along the nematic director was studied by atomic force microscopy, measurements of electrical conductivity and Raman spectroscopy of the composite in the directions parallel and perpendicular to the nematic director. The composites were prepared through dispersion of SWNT with LC monomer in a common solvent, their alignment in nematic monomer and consequent UV polymerization of the monomer. The anisotropy of electrical and optical properties of the system depends strongly on the concentration of the nanotubes in the range of 1-10% SWNT being especially strong for smaller concentrations and negligible at higher loads. A simple semi-quantitative model is suggested to account for the orientational behavior of nanotubes in nematic matrices. It successfully describes the observed anisotropy of physical properties at microscale (up to 200 μm) in terms of anchoring of the polymer chains to the nanotubes surface and adjustment of the nanotubes orientation to the nematic direction due to such coupling. The increasing disorientation of the nematic domains at higher nanotubes loads is explained as a development of larger number of LC defects induced by the nanotubes in the nematic matrix due to their intrinsic nature of aggregation. The anisotropy of physical properties at macro scale (several millimeters) is much smaller and less dependable on SWNT concentration because differently oriented LC domains effectively wash out the anisotropy.     

低铁耗条件下转炉高碳低磷工艺实践与应用

对转炉炼钢实现低铁耗和高碳低磷工艺进行了分析，介绍了南钢公司转炉炼钢实践低铁耗条件下高碳低磷工艺的具体应用措施。     

二氧化碳与磷化氢混合熏蒸防治储烟害虫试验

目前,储烟害虫防治普遍采用磷化铝片剂常规熏蒸法,磷化铝施用量为6～9g/m3,安全上存在一定的隐患。为了减少磷化铝用药量,于2003年应用微电脑控制的仓外混合熏蒸机,施用钢瓶装液化二氧化碳和56%磷化铝片剂,进行了二氧化碳与磷化氢混合熏蒸杀虫试验,以8g/m3磷化铝常规熏蒸法为对照。试验结果表明,磷化铝施用量为2.3g/m3、二氧化碳施用量为12g/m3,混合熏蒸结果达到100%杀死害虫。与对照相比,杀虫效果相同,混合熏蒸法具有磷化铝施用量较小、较为安全和有利于减少污染等优点。     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Polymer transcrystallinity induced by carbon nanotubes

In this work, we provide the evidence of polymer transcrystallinity in the presence of carbon nanotubes (CNTs). The interfacial morphology of carbon nanotube fiber-polypropylene matrix is investigated by means of polarized optical microscopy (POM), wide-angle X-ray diffraction (WAXD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The supramolecular microstructures of polypropylene transcrystals induced by the nanotube fiber are observed in the range of isothermal crystallization temperatures from 118 °C to 132 °C. The dynamic process of transcrystallization is analyzed by using the theory of heterogeneous nucleation. Microstructure analysis shows that the nanotubes can nucleate the growth of both α- and γ-transcrystal, and α-transcrystals dominate the overall interfacial morphology. Close to the nanotube fiber surface, a cross-hatched lamellar microstructure composed of mother lamellae and daughter lamellae is observed.     

影响带锯机锯切质量的原因及处理措施

通过对锯切装置的改进，提高了锯切性能，降低了锯条成本，保证了锯切质量，使设备更加高效、安全的工作。     

电子工业用高纯氮的生产

生产电子工业用高纯氮的制氮装置 ,其要点和难点是一氧化碳和氢的清除。采用一氧化碳转换炉和特殊的冷箱内流程组织 ,可以生产纯度为 99 9999%以上的高纯氮。对制取电子工业用高纯氮制氮装置与常规制氮装置加氮终端净化器两种流程进行了比较。