环氧-聚酰胺体系中增韧剂的研究

在环氧-聚酰胺体系中分别加入“海岛结构”QS-1、聚硫橡胶、液体丁腈橡胶增韧改性,通过对固化物剪切强度、弯曲弹性模量及断裂强度的对比,“海岛结构”QS-1增韧综合性能较好.     

用弯曲模型推导二组元复合材料杨氏模量新公式

用弯曲模型推导了适用于悬丝耦合弯曲共振法检测金属第二组元的杨氏模量的理论公式。通过实验数据计算。结果表明在两组元h2/h1≈1时与文献[2]的计算结果几乎接近，为用悬丝耦合弯曲共振法检测各种减振材料，陶瓷材料杨氏模量提供了理论公式；同时用改进后的弯曲模型推导出了适用于纤维复合材料横向杨氏模量的预测公式。     

Adhesion and Hydrolytic Stability of the Interface Between High-Modulus Polyethylene Fibers and Acrylic Resins

The effects of oxyen plasma treatment on the surface chemistry of Spectra 1000® high modulus polyethylene fibers and on the mechanical properties of fiber-reinforced composites of the fibers in a Bis-GMA based acrylic resin have been studied. X-ray photoelectron spectroscopy and diffuse reflectance FTIR spectroscopy have been used to show that the majority of oxygen on the fiber surface exists mostly in the form of ether and/or epoxy linkages, with carbonyl-, carboxylic- and ester-containing compounds accounting for less than 10 percent of the total. While the untreated and plasma-treated fibers have similar chemical compositions, the surfaces of the plasma-treated fibers are more polar and the oxygen is chemically bonded instead of being merely physisorbed. The interfacial shear strength between the fibers and the acrylic resin is increased by a factor of 2.3 by the plasma treatment indicating the presence of a weak boundary layer on the surface of the untreated fibers. The hydrolytic stability of the composite interfaces was investigated for fibers sized with several Bis-GMA-based adhesives. Maximum stability was attained by sizing with Bis-GMA containing a peroxide catalyst or an amine accelerator. The flexural properties of composites utilizing plasma-treated and untreated fibers were compared in three-point bending. The ultimate bending loads for composites using treated fibers were much higher than those for composites with untreated fibers, but only a fraction of that for glass or Kevlar®-reinforced materials.     

考虑纤维波动[＋φ／-φ]缠绕角管件的轴向弹性模量计算方法

本文在计算[ φ/-φ]缠绕角管件的轴向弹性模量时,通过引入纤维波动程度参数来计入纤维波动的影响,理论计算结果与层板理论计算结果相比更接近实验结果,说明本文提出的算法,可在一定程度上计入纤维波动的影响。     

PVC-U型材弹性模量测试偏差分析

在对PVC-U型材弹性模量试验中发现，同一样品的规则样条与不规则样条的弯曲弹性模量相差较大。不规则样条的负荷-挠度曲线上会出现拐点，如果不对曲线进行处理直接计算得到的弯曲弹性模量偏小。在不规则样条的负荷-挠度取拐点后直线段切线与横坐标的交点作零点修正后所测得的弯曲弹性模量比较接近真实值。通过实验可以验证处理后的方法测得的弹性模量与均匀规则样条的弯曲弹性模量相近。     

单向Cf/SiC复合材料的弯曲疲劳性能

对单向Cf/SiC复合材料进行了三点弯曲疲劳性能测试,得到了复合材料的应力－寿命曲线（S－N曲线）,并对其进行线性拟合,得到疲劳最大应力与复合材料疲劳寿命的关系;考察了疲劳过程中刚度下降和疲劳裂纹产生情况。结果表明在疲劳过程中复合材料的弯曲模量有3个变化阶段：首先在疲劳加载初期,弯曲模量的下降速度及幅度都较大;其次在弯曲模量下降到原始弯曲模量的85％（133GPa)后,其变化方式没有明显的规律可循,有时甚至可能上升;最后复合材料发生疲劳断裂时,模量将发生突变。显微结构分析表明：基体横向裂纹群的产生是疲劳断裂的独有特征。它的产生是由于基体SiC的断裂应变小于碳纤维的断裂应变,基体首先开裂并导致应力重新分布的结果。     

稀土丁异戊橡胶改性天然橡胶的应用研究

采用稀土丁异戊橡胶代替顺丁橡胶，测试并分析了改性天然橡胶的低温性能及相关性能。结果表明，稀土丁异戊橡胶改性的天然橡胶室强力学性能和粘接性能与顺丁橡胶改性的天然橡胶相近，但低温性能有较大的改善。在-40℃下贮存2h后，顶丁橡胶改性天然橡胶硫化胶有明显的结晶现象，其剪切模量较室温下的相应值增加了6倍，而稀土丁异戊橡胶改性的天然橡胶硫化胶保持了良好的弹性，其剪切模量值与室温下的相当。     

Shear Strength of Pressure Sensitive Adhesives and its Correlation to Mechanical Properties

Correlations between shear resistance and the mechanical properties of pressure sensitive adhesives are studied by measuring the deformation behaviour in the static and the dynamic shear test and determining the dynamic shear modulus of the adhesive. For polymers with low or moderate viscosities, the shear strain vs. time characteristics in a static shear test and, accordingly, the static shear strength, can be evaluated from the master curves of the dynamic shear modulus or the dynamic viscosity. The dynamic shear strength also can be calculated. These exact calculations cannot be applied to highly viscous or slightly crosslinked polymers. On the basis of the model experiments, empirical correlations between shear strength and the dynamic shear modulus are established which seem to be generally valid.     

The effect of various slaked limes on the microstructure of a lime-cement-sand mortar

The present work aims to provide a better understanding of the effect of both the proportions and the characteristics of slaked lime on the microstructure of a lime-cement-sand mortar. Cement (CPA CEM I 52.5) has been replaced by various categories of slaked lime chosen for the diversity of their physico-chemical characteristics.Cement has been replaced by lime in proportions varying between 0 to 10% of the total binder mass. With very few exceptions, mortars were produced by maintaining the quantity of water constant.Experimental results show that it is necessary to have a high lime substitution percentage to influence the microstructure of the mortar, except in the case of a lime containing magnesium hydroxide or calcic lime featuring sizeable specific surface area.The influence of the nature of the substituted lime on the development of the microstructure in the matrix has been examined by SEM observations of the mortar micro porosity.     

Application of orthogonal collocations to some transport phenomena problems in co-axial cylinders and spheres

Collocation methods are developed for the solution of some differential equation models for transport phenomena problems in one-and two-dimensions in co-axial annuli of spherical and cylindrical shapes. General formulae are developed to obtain orthogonal polynomials over an arbitrary interval using two types of weighting functions. The convergence and accuracy of the methods are demonstrated using two test problems, i.e., calculation of effectiveness factors in (a) a spherical pellet with peripherally deposited catalyst and (b) a Raschig ring type cylindrical catalyst pellet. Comparisons of results obtained from the present methods with analytic solutions for the first-order reactions indicate good agreement. Numerical solutions are also obtained for the second-and the third-order reactions for which analytic solutions are not available. Results obtained in terms of a new Thiele modulus involving the ratio of volume of peripherally deposited part of catalyst to exterior surface area indicate that this normalization brings effectiveness factor versus Thiele modulus curves close together for co-axial spherical and long cylindrical pellets, as it does for these geometries without the inner co-axial portion.