钢铁表面黑色转化膜处理技术

黑色转化膜技术是目前较为先进的钢铁表面处理技术 ,本文试验研究了一种新工艺 ,提出了TB值的概念 ,通过控制TB值即可控制处理液的质量 ,获得性能优良的转化膜。此工艺性能可靠 ,可操作性强 ,并可应用于激光热处理前的预处理。     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

The development of MHD cold wall channels in the oil-fired condition

The durability of a cold wall MHD generator consisting of metal electrodes and alumina-coated peg insulators was experimentally examined in the oil-fired MHD condition with the additive of SO₂ corresponding to S = 0.54 wt%. The structure of the electrode wall and various anode and cathode materials were tested, with particular reference to developing long-life electrodes. It was clarified that Pt, SHOMAC (28.8 Cr−1.9 Mo) and SUS-304 as anodes and W---Cu (70 W−30 Cu) and WC---Ag (60 WC−40 Ag) alloys as cathodes were promising for durability and that the structure of an anode divided into two elements connected to each other with an SnO₂ resistor was very useful for uniformity of the anode corrosion pattern and the inter-anode voltages. It is reasonable to expect, from the test results, that the lifetime of a cold wall MHD generator in an oil-fired commercial plant will be over 4000 h, and therefore, a foundation for its commercial use has been established.     

ARMA噪声中的正弦波检测

本文提出一种ＡＲＭＡ噪声中正弦波检测的方法，本方法先用改进的Ｐｒｏｎｙ法估计可能存在的正弦波，然后利用一种综合考虑衰减因子以及ＭＵＳＩＣ值的准则从估计结果中区分正统率波的真伪。数值例子表明，本文方法比Ｐｒｏｎｇ方法及ＭＵＳＩＣ方法具有更高的分辨力。     

微机在应变测量中的应用

微机在应变测量中的应用，采用上位机和下位机组合方式．上位机为一台ＩＢＭ－ＰＣ／ＸＴ微机，用于对数据进行后处理．下位机以Ｚ８０－ＣＰＵ为控制器，由传感器、转换器、接口及外设等组成数据采集器，实施对应变、压力和位移等参数的采集、显示和打印（即数据的预处理）．上位机和下位机之间的数据传输，采用串行的方式，通过ＲＳ－２３２接口完成．本文主要以应变的采集处理为例，介绍系统功能、硬件配置及软件设计．     

国产CN—31催化剂与ICI65—2催化剂工业应用的比较

国产轻油预转化催化剂与进口催化剂相比,具有性能相当、价格低廉、供应方便等优势。国产预转化催化剂需在较高的液空速、温度较低的条件下实现烃类转化反应,生成含甲烷60%以上的富气。采用国产催化剂能明显反映性能价格比。文章对两种催化剂进行了工业应用比较和分析。     

数字视频混合系统的设计

介绍了利用Philips的一款视频芯片SAA71 99B实现的数字视频混合系统.该系统可以将一路PAL制彩色复合视频信号编码进入另一路PAL制彩色复合视频信号中,以取代第二路视频中用户指定的颜色,从而实现了两路视频的混合.另外还介绍了如何利用单片机的I/O口模拟I 2C总线以及如何利用单片机进行彩色空间变换的算法.     

功率因数的概念及测试方法探讨

随着理论的发展和技术的进步，功率因数的概念有了更深的内涵，本文就其概念作了说明，对测量方法作了探讨。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

A novel laboratory bench for practical evaluation of catalysts useful for simultaneous conversion of NOx and soot in diesel exhaust

This study deals with the development of a laboratory bench for the practical evaluation of catalysts that are useful for the direct conversion of NO_x and soot in the exhaust of diesel engines. The employed model exhaust is generated by using a diffusion burner with additionally dosing some gaseous components to the burner gas to obtain a realistic feed composition. The produced soot is extensively characterized by employing thermogravimetry, transmission electron microscopy, N₂ physisorption and temperature programmed techniques. The results of the different characterization methods show that the present soot is suitable for the intended catalytic investigations. The simultaneous conversion of NO_x and soot is examined like in practice, i.e. the soot is separated from the tail gas by a diesel particulate filter (DPF) that is coated with the catalyst. The deposited soot is then catalytically converted by NO_x and O₂ to form N₂ and CO₂. The conversions of NO_x and soot are measured by exclusively applying gas analysers, whereby a special experimental procedure is developed to determine the soot removal. Hence, additional soot related analytics are not required. To show the suitability of the constructed bench a Pt/Fe₂O₃/β-zeolite sample is taken as test catalyst that is reported to be very active in NO_x/soot reaction. The measurements performed with and without catalyst clearly show the effect of the used sample in simultaneous NO_x/soot conversion. We therefore consider the constructed laboratory bench to be a useful tool for testing and ranking catalytic materials.