基于PTFE的PCB的多层层压方法

介绍了采用不同材料类型的粘结膜、半固化片、所需设备和粘结材料,用于生产低到高层数的PTFE多层板的情况。     

用SY87721实现城域网波分复用系统的多业务接入

为了使城域网的DWDM（密集波分复用）系统可以接入多种信号速率和格式，以满足用户的要求，首先介绍了一种波长转换板的设计方法，使用SY87721自适应提取28Mbit／s～2.7Gbit/s之间任意速率信号的时钟，其次介绍了SY87721提取时钟的工作原理、与单片机和CPLD（复杂可编程逻辑器件）的接口方式、对寄存器的配置和读出方式。最后介绍了使用参考时钟测量接入信号频率的方法，这会在系统维护时带来较大的方便。     

Synthesis and characterization of polyaniline films using Fenton reagent

The chemical oxidation of aniline to form polyaniline (PANI) films and powder samples was made using Fenton reagent as an oxidizing agent in aqueous sulfuric acid medium. The PANI films were monitored by using the quartz crystal microbalance and the electronic absorption techniques. The optimum concentration was determined and the results were justified by measuring the UV–vis absorption spectra for the in situ PANI films. The conductivity for the PANI films and powder samples, prepared in different conditions, was measured. Also, the IR spectra, X‐ray and the thermogravimetric analysis for the PANI powder formed in the bulk were measured and compared with the polymer prepared using ammonium peroxydisulfate. A preliminary investigation to the dielectric properties of the polymer powder was measured and discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polymerization strategies to overcome limiting monomer conversion in silicone-acrylic miniemulsion polymerization

The limiting conversion phenomenon observed in high solid content silicone-modified acrylic miniemulsion polymerizations was investigated. It was found that the limiting conversion was mainly due to the formation of inactive radicals upon propagation of butyl acrylate radicals with the vinyl end groups of the polydimethylsiloxane. Polymerization strategies that allowed overcoming this problem and achieving high monomer conversion were implemented.     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

伴随内转换电子发射的俄歇电子能量及强度计算

简要介绍了伴随内转换电子发射产生的俄歇电子能量与强度的计算方法、计算程序及工作流程，并以^129Iβ^-衰变为例说明其具体应用。     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.     

Improvement of photon collection in Cu(In,Ga)Se2 solar cells and modules by fluorescent frequency conversion

Fluorescent photon down conversion for the improvement of the blue response of ZnO/CdS/Cu(In,Ga)Se₂ heterojunction solar cells and modules is investigated. Fluorescent dyes of the series Lumogen® F are analyzed by optical transmission and reflection as well as by photoluminescence measurements. A spectral transfer matrix formalism is introduced that allows to predict the suitability of a luminescent dye as a down-converter for a given solar cell from its absorption/emission properties. We find that Lumogen® F Violet 570 and Lumogen® F Yellow 083 as well as a combination of both yields improvements for Cu(In,Ga)Se₂ solar modules. Particularly, we find that the short circuit current density of a Cu(In,Ga)Se₂ mini-module is improved by 1.5 mA cm^− 2 when applying a varnish with a combination of Lumogen® F Violet and Yellow. About 0.5 mA cm^− 2 of this improvement is due to a reduced overall reflectance and an improvement of 1 mA cm^− 2 results from the frequency conversion by the dyes.     

Synthesis of Hexagonal‐Phase NaYF4:Yb,Er and NaYF4:Yb,Tm Nanocrystals with Efficient Up‐Conversion Fluorescence

IR‐to‐visible up‐conversion fluorescent nanocrystals of hexagonal‐phase NaYF₄:20 %Yb,2 %Er and NaYF₄:20 %Yb,2 %Tm have been synthesized by decomposition of multiprecursors of CF₃COONa, (CF₃COO)₃Y, (CF₃COO)₃Yb, and (CF₃COO)₃Er/(CF₃COO)₃Tm in oleylamine at 330 °C. The average particle size is 10.5 ± 0.7 nm (from random measurements of 200 particles from five transmission electron microscopy images) and 11.1 ± 1.3 nm (from dynamic‐light‐scattering measurements). The up‐conversion fluorescence intensity of the hexagonal nanocrystals in this work is much higher than that of other cubic‐phase NaYF₄:Yb,Er nanocrystals, including the ones in this work (by a factor of 7.5). Mechanisms for nucleation and growth of the hexagonal‐phase nanoparticles are proposed. These nanocrystals are easily dispersed in organic solvents, producing a transparent colloidal solution. The hydrophobic surfaces of the particles are made hydrophilic using a bipolar surfactant. These nanoparticles and their dispersions in various media have potential applications in optical nanodevices and bioprobes.