Effect of Bi and Sr concentrations on the formation of the 2223 phase in Bi-Pb-Sb-Sr-Ca-Cu-O materials, obtained under different conditions of thermal treatment

The superconducting properties and the phase and chemical composition of Bi _x Pb_0.3Sb_0.1Sr _y Ca₂Cu₃O_z (x=1.5, 1.6, and 1.7;y=1.9, 2.0, and 2.1) materials synthesized by one-step and multistep thermal treatments have been investigated. The multistep annealing between 825–875°C promotes the 2223 phase. The change of Bi concentration has little effect on the 2223 phase formation, regardless of the kind of thermal treatment used, but increasing the Sr concentration (y> 2) strongly inhibits this phase. It has also been established that the loss of Pb after synthesis depends on the initial Bi concentration. The loss of Pb decreases when the initial Bi content is lower.     

热处理WO3电变色膜稳定性研究

采用电子束蒸发淀积ＷＯ３薄膜。根据已有的ＷＯ３薄膜脱水过程结论而选择适当温度对薄膜进行退火处理。在大量含水的和不含水的两类Ｌｉ＾＋电解质中进行比较性着色和消色循环实验，表明在２９０℃以下热退火处理能明显增加ＷＯ３薄膜在含水 电解质中的循环寿命。     

均匀化退火对Al－Mg－Li（01420）合金加工性能及力学性能的影响

通过对０１４２０合金的均匀化退火，研究了均匀化制度对合金热加工性能和力学性能的影响。结果表明：均匀化制度对合金性能的影响很大，均匀化不足或过烧都会使合金热轧开裂和塑性降低。经过４７５℃×４８ｈ退火后，主合金元素Ｍｇ的分布均匀，合金可获得最好的综合性能。     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

无规聚苯乙烯的物理老化研究进展

从无规聚苯乙烯(aPS)体积驰豫和结构驰豫的过程解释了aPS物理老化的现象,以及物理老化和退火对其物理性能的影响。总结了利用现代的研究方法对aPS玻璃化转变和松弛的研究状况。     

A heuristic for the label printing problem

Label printing finds many applications in industry. However, this task is still labor intensive in many printing factories. Since each template can only accommodate a fixed number of labels, an important task is to work out the compositions of templates by allocating suitable labels to each template in order to fulfill the order requirements effectively. The template design could be rather arbitrary, which usually ends up with a lot of excessive printed labels. Enhancing the template design will significantly improve the efficiency of the printing process, and, at the same time, reduce the waste of resources. This motivates the study of more automatic design methods. In this paper, the problem is first formulated as a nonlinear integer programming problem. The main variables in the formulation are the compositions and the printing frequencies of templates. For practical purpose, each type of label is confined to one template only which allows automated packing and handling. The structure of the problems is carefully analyzed and a new algorithm is proposed. Numerical results show that the proposed method is a simple but effective way of generating good template designs.     

激光结晶a-Si:H SOI离子注入和快速退火

本文对激光结晶a-Si∶H SOI结构砷注入和快速退火行为作了研究.a-Si∶H激光结晶有Lp-LCR,OD,FCR-2,FCR-1四个结晶区.用剖面电镜观察了结晶区的结构.扩展电阻测量表明Lp-LCR区中有两种扩散机制,即杂质在晶粒体内扩散和沿缺陷扩散.OD区中有三种扩散形式,除有上述两种以外,还有沿缺陷的扩散.首次比较了沿晶界和缺陷的扩散速度.     

溶胶-凝胶生物玻璃多孔材料显微结构和生物活性的扫描电镜及红外光谱分析

本文利用溶胶．凝胶法制备了CaO-P2O5-SiO，系统生物活性玻璃，并以其为原料制备了用于骨修复及骨组织工程支架的块状生物活性材料。利用体外实验方法(invitro)结合x射线衍射(XRD)、扫描电子显微镜(SEM)和傅立叶变换红外光谱分析(FTIR)技术对不同烧结工艺制备的材料结构、晶相和生物活性的影响进行了分析研究。研究表明，经800℃和1100℃烧结5min的两种材料均有硅磷酸钙Ca5(PO4)2SjO4微晶相析出。烧结温度越高，析出微晶相的体积比例越大，材料的生物活性则越低。在模拟生理溶液中碳酸羟基磷灰石(HCA)只在烧结体中的玻璃颗粒表面形成，而在其硅磷酸钙Ca5(PO4)2SiO4微晶相表面未发现HCA形成。     

SAR图像组合分割算法

由于存在乘性斑点噪声的影响,给SAR图像分割造成很大困难,本文研究利用最大似然区域增长分割算法,提出区域增长前引入自适应边缘检测,图像分割性能获得较大提高.介绍了我们研究的分割性能优异的模拟退火分割算法,提出了分割性能接近模拟退火并且在SAR图像分割中比较实用的模拟退火和最大似然混合分割算法,并给出了这些分割算法的分割性能比较,以及在实际分割SAR图像时应当如何选择分割算法.     

具有网络功能的虚拟演播室在电视节目中的应用

在对具有网络功能的虚拟演播室介绍的基础上，结合实践，着重讨论了如何将虚拟演播室系统应用于电视节目制作中及操作人员对演播室系统的适应性、虚拟演播室系统存在的问题。