Influence of Nucleation Agents Concentration on Crystallization Structure and Properties of Glass-ceramics

Deep color glass-ceramics is prepared by using gold tailings as the main raw material, and Cr2O3 is added as nucleation agent. Influence of different Cr2O3 additions on crystallization structure and properties of CaO-MgO-Al2O3-SiO2 glass-ceramics has been discussed so as to select optimum additions. DTA is employed to determine optimum crystallization and nucleation temperatures; XRD and SEM are used to characterize microstructure of each sample; and performance indexes, such as water absorption, bulk density, flexural strength and so on, are also determined. Experimental results show that when 3wt% Cr2O3 is introduced, fine glass-ceramics with diopside as the main crystal and Ca-Fe diopside as the second-crystal is obtained, and its corresponding performance indexes are as follows: water absorption 0.12%, bulk density 2.56 g/cm3, and flexural strength 70.01 Mpa.     

La2O3对钛合金表面镍基喷焊涂层组织和性能的影响

采用火焰喷焊技术在钛合金基体上制备了不加La2O3和加4％(质量分数)La2O3两种镍基涂层，分析了它们的显微组织、合金元素的扩散、显微硬度以及耐磨性能。结果表明：La2O3的加人，改善了涂层合金的流动性和显微组织的均匀性，并使涂层与基体的熔合更加明显，结合性能得到进一步提高；虽然一定程度上减弱了基体Ti元素对喷焊层的强化作用，使表层显微硬度略有下降，但磨损失重却较未加La2O3的喷焊涂层下降了20％。     

Characterization of a convection-based support microstructure through a flow resistance parameter

Modern convection-based supports differ substantially in pore size, porosity, and microstructure topology. Due to such variability, it is challenging to evaluate the contribution of a particular microstructure topology on flow resistance. We demonstrated that the flow resistance parameter ($\varphi$) introduced decades ago can be used as a criterion to evaluate the effect of microstructure topology on a pressure drop when the pore size is used as a characteristic support dimension. Furthermore, the $\varphi$ value of simple cubic packing was calculated over the entire range of open porosity and compared to the $\varphi$ values determined for pressure drop models derived for particular convection-based supports and experimental values of various convection-based supports from the literature. It was shown that different convection-based supports become clustered into distinct groups when plotted according to their $\varphi$ and open porosity values, allowing their discrimination.     

Controlled ring‐opening polymerization of propylene oxide catalyzed by double metal‐cyanide complex

A double metal‐cyanide catalyst based on Zn₃[Co(CN)₆]₂ was prepared. This catalyst is very effective for the ring‐opening polymerization of propylene oxide. Polyether polyols of moderate molecular weight having low unsaturation (<0.015 meq/g) can be prepared under mild conditions. The molecular weight of polymer is entirely controlled by a reacted monomer‐to‐initiator ratio. The polymers prepared with stepwise addition of monomer exhibit a narrower molecular weight distribution as compared with those prepared with one‐step addition of monomer. Various compounds containing active hydrogen, except basic compounds and low‐carbon carboxylic acid, may be used as initiators. The reaction rate increases with increasing catalyst amount and decreases with rising initiator concentration. Polymerization involves a rapid exchange reaction between the active species and the dormant species. It was also proven that, to a certain extent, the chain termination of this catalytic system is reversible or temporary. ¹³C NMR analysis showed that the polymer has a random distribution of the configurational sequences and head‐to‐tail regiosequence. It is assumed that the polymerization proceeds via a cationic coordination mechanism. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1142–1150, 2002     

Structural Efficiency and Microstructural Modeling of Wet Gels and Aerogels

We present a microstructural model of aerogels that includes the effect of particle necks, tortuosity and dangling ends on the scaling of elastic moduli with density. Relative neck radii can be determined for sintering series of silica aerogels and for Resorcinol Formaldehyde (RF) aerogels produced with different catalyst concentrations. The density of elastically ineffective dangling ends and the tortuosity can be estimated using information from thermal conductivity and elastic modulus measurements in silica aerogels. Typical values for the load bearing mass range from >50% for high density and heat treated aerogels to <10% of the total mass for low density wet-gels.     

Ag(TCNQ)准一维微米结构的制备及表征

利用溶液化学反应法制备了准一维结构的金属有机配合物Ag(TCNQ). X射线衍射(XRD)表明，所制备的Ag(TCNQ)为晶态结构;扫描电子显微镜(SEM)的观察证明，Ag(TCNQ)为准一维的微米管或线；Raman 测试结果表明，单根的Ag(TCNQ)形成时,Ag原子与TCNQ分子之间发生了电荷转移.对样品的制备工艺,即 Ag膜厚度和浸入溶液的反应时间对生成Ag(TCNQ)晶体形貌的影响进行了研究.结果表明，Ag膜越薄，生长出的晶体越稀疏;Ag膜与TCNQ乙腈溶液的反应时间影响其形貌的变化.反应历经三个阶段,晶体形成和长大阶段、反应完全阶段及溶解阶段.     

The microstructure and optical transmittance thermal analysis of sodium borosilicate bio-glasses

The conditions to fabricate the bulk porous specimens have been studied on account of sodium borosilicate (NBS) glasses. Glass composition, heat treatment at phase separation and TiO₂ addition have been considered in this study. Original glass samples of composition in mol%: sample A: 9.19 Na₂O - 23.58 B₂O₃ - 67.23 SiO₂, sample B: 9.29 Na₂O - 3.17 TiO₂ - 23.82 B₂O₃ - 63.72 SiO₂ were prepared by melting reagent grade chemicals (Na₂CO₃, HBO₃, SiO₂ and AgNO₃) in platinum crucibles at 1480°C for 1 h in air. The melts were poured onto stainless steel plates and were annealed at 500°C for 0.5 h after cooling. Thus, obtained samples were phase separated at 700°C for 2, 15, 25 and 50 h to study their microstructure by scanning electron microscope (SEM). Besides the direct study of the microstructure by SEM, information on glass structural changes of samples are provided by measuring in situ changes by the optical transmittance thermal analysis. The isothermal measurements were carried out at 700, 720 and 740°C. The temperature of phase separation, the leaching and nucleator addition (TiO₂), significantly influence the microstructure of the resulting leached product. TiO₂ additive seems to suppress crystallization of cristobalite: especially at the extended above heat treatment phase separation runs. The phase-separated domains of glasses containing above 80 moles of SiO₂ are so small that it is very hard to observe them by SEM. The glass composition in our case was selected in a way to have relatively large phase separated areas easily observed by SEM at magnification 20 000·. The influence of TiO₂ is not too pronounced. It seems to suppress the cristobalite crystallization, especially of longer heating runs. The image analysis of leached glasses shows the prevailing content of the skeletal phase in a comparison to pores. The TiO₂ content diminishes the content of the skeletal phase. This revised version was published online in July 2006 with corrections to the Cover Date.     

Microporous SiO2 and SiO2/MOx (M=Ti,Zr, Al) for ceramic membrane applications: A microstructural study of the sol-stage and the consolidated state

Microporous SiO₂ and SiO₂/MO₂ (M=Ti, Zr, Al; 10 mol% MO_x) materials for gas separation membrane applications have been prepared from polymeric sols. Characterization of these sols with SAXS showed that the mean fractal dimension of the SiO₂ sols is 1.3–1.4 with a radius of gyration of approximately 2.5 nm. The dried and calcined films are microporous and the pore size distribution was bimodal with maxima at diameters of 0.5 nm and 0.75 nm. For the SiO₂/TiO₂, SiO₂/ZrO₂ and SiO₂/Al₂O₃ systems, much milder reaction conditions proved to be necessary to obtain sols with comparable fractal dimensions due to the high reactivity of the Ti/Zr/Al-alkoxides. Microporous supported membranes with molecular sieve-like gas transport properties can be prepared from a relatively wide range of sol structures: from polymers too small to characterize with SAXS to structures with fractal dimensions: 1<d _f<2.04.     

TiO2表面电子结构及其光催化活性

利用ＨＣｌ和ＨＣｌＯ４对不同方法制备的ＴｉＯ２进行了表面修饰,发现经强酸修饰后ＴｉＯ２的光催化活性有明显提高,其中ＨＣｌ的修饰效果好于ＨＣｌＯ４。     

Lattice orientation within stirring-induced crystals of polyethylene

Micro-shish-kebab stirring-induced polyethylene crystals, as defined and described in the preceding paper, are flat, ribbon-shaped fibers. Selected area electron-diffraction techniques were used to determine the orientation of the crystal axes with respect to the external fiber shape. It has been shown that in addition to the crystal-lographic c-axis laying along the fiber direction, the normal to the ribbon plane is parallel to the crystallographic a-axis.