钢纤维聚合物混凝土抗压本构关系

钢纤维聚合物混凝土是由聚合物混凝土基体和钢纤维共同组成的纤维增强复合材料，它的力学行为不仅依赖于聚合物混凝土基体的行为，而且与钢纤维的掺量、分散特征以及钢纤维的几何尺寸有关，本文将基于损伤力学原理研究在不同纤维掺量下的钢纤维聚合物混凝土的全程压力-应变曲线及其本构模型。     

Methane/natural gas storage and delivered capacity for activated carbons in dry and wet conditions

Methane/natural gas storage and delivered capacity for three different activated carbons in dry and wet conditions were measured. In all tests the temperature of the bed was maintained constant at 277.15 K and pressure was increased up to 10 MPa. Natural gas storage capacity was less than methane storage capacity in dry conditions for all the three activated carbons tested, while the gas delivery was almost the same. One of activated carbon tested (NC120) showed the possibility of hydrate forming for pressures higher than 4 MPa but the amount of gas stored still was less than the amount stored in dry conditions over the whole range of pressure. The analysis of the gas delivered at each pressure steps shows that considerable amount of heavy components do not come out from the bed even at very low pressures in both dry and wet condition tests. Repeatability of the sorption/desorption processes - vital for possible commercial/industrial use - has been examined over various cycles.     

Visualization and quantification of the mechanical deformation induced by an electrical field in poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) films

An optical nondestructive strain measurement technique was performed to analyze the mechanical deformation induced by an electrical field within the insulating materials. Poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) films were then subjected to constant electrical fields right up to their electrical breakdown. The experimental technique made it possible to follow the various stages of the mechanical behavior of PEN in real time. The final breakdown occurred in the observation zone and the related mechanical deformation was captured. A “margarita” structure was observed with a hole at the center. The experimental results indicated that the level of the induced‐mechanical deformations depended on the local environment. We defined two different zones representing the inside and the outside of the damaged area. The induced‐deformations were larger in the damaged zone. It was also observed that deformations increased when the sample had a lower degree of crystallinity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

三探测器密度测井数据处理方法研究

数据处理方法研究是三探测器岩性密度测井研究的一个重要方面。在Monte Carlo模拟的基础上，提出了2种三探测器岩性密度测井求取地层光电吸收指数Pe和进行泥饼校正求取地层密度ρb的方法；就三探测器岩性密度测井仪DTLD—2的围岩补偿功能进行了研究。结果显示了用计算机模拟方法研究核测井问题可以节省建造实体物理模型的费用和人力，具有广泛的应用前景。     

地层测试对油层改造选井选层的重要性及改造措施有效性评价

经对胜利油田近三年来典型井例测试资料分析评价及其增产措施效果分析认为，有三类地层压裂增油效果很好：地层物性相对较好的常压系统且存在严重堵塞的储层；物性较好的常压地层；高压低渗透储层。有两类地层酸化效果很好：灰岩、白云岩裂缝、低产低渗透储层；物性较好且存在严重污染堵塞的储层。其它地层压裂、酸化一般是无效的。     

Multiwalled Nanotubes: Their Formation by Irradiating Graphite with High Doses of Electrons

We report the production of carbon nanotubes by high dose of electron irradiation. The irradiation was performed with a 2 MeV Van de Graaff accelerator, while the irradiation conditions were the following: voltage 1.3 MeV, current 5 µA, dose rate 25 kGy/min, and total dosage 1000 kGy. The samples were analyzed in a high-resolution transmission electron microscope. The main features observed on the samples, were huge nanotubes of several nanometer long and few nanometer wide, which are capped at one end. It is good to point out, that at this level of irradiation, we were not able to find either onion-like or particle structures throughout the material, as it is usual in similar hexagonal structures. This behavior could be attributed to the level of irradiation used to create the nanotubes under investigation.     

超低渗广谱油层保护技术在板深51区块的应用

板深51区块存在压力敏感地层，在非目的层井段存在大段高渗低压砂岩，而目的层又属于高压低渗地层，属于难采油气田。室内进行的砂床滤失量、砂床封堵带承压能力、岩心封堵带的承压能力及油气层保护效果实验表明，在超低渗钻井液中增加固相含量，能够提高超低渗透膜结构强度，提高地层承压能力，降低砂床侵入深度，增强保护油气层效果，而且有选择性地增加有用固相效果更佳。基于这一理论，研究成功了超低渗广谱屏蔽暂堵油层保护技术，并在板深51区块长22—15井和长23—17K井进行了试验应用。该技术的关键是依据地层特性确定复配暂堵剂。长22-15井和长23-17K井射孔后未经过压裂、酸化、排液处理，获自喷高产，尤其是长22-15井形成自喷油流，创油田单井试采产量最高记录。应用结果表明，超低渗广谱保护油气层钻井液技术封堵隔层的承压能力强，很大程度地提高了漏失层的承压能力和破裂压力，较好地解决了含多套压力层系长裸眼段钻井过程中发生的漏失、井喷、卡钻、油气层保护等技术难题。     

高功率激光系统通过空间滤波和中继成像抑制自聚焦

讨论了由光束自聚焦引起的细丝形成和光束分裂，为了克服聚焦造成的破坏要求在光束传播中采用中继成像和空间滤波。     

On modeling the design of cellular manufacturing systems

A new optimization model is discussed for the design of cellular manufacturing systems. It is based on an integer programming formulation that updates some other models by eliminating redundant machine assignment and cost coefficients dependent on cell configuration. To reduce computational burdens, a simplified integer programming model and a decomposition algorithm are proposed. Several computer solutions were performed to evaluate the performance of the new model. The computational results are discussed.