C5/C6异构化催化剂的首次工业应用

采用中石化金陵分公司研究院研制的CI-50(Pd/丝光沸石)作C5/C6烷烃异构化催化剂.详细介绍了该催化剂的工业放大试验装置的工艺流程、首次开工过程中技术问题及处理方法.     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

交流变频调速技术在二辊轧机压下系统中的应用

介绍一种采用变频调速技术控制的二辊轧机压下系统。该系统可控制轧机压下系统的速度在工艺要求的范围内无级可调，压下量以数字动态显示，控制准确、操作方便。文中对系统的组成及工作原理作了较详细的介绍。     

Pit to crack transition in stress corrosion cracking of a steam turbine disc steel

Long term exposure tests have been carried out on a 3 NiCrMoV steam turbine disc steel in the form of cylindrical tensile test specimens self-loaded to 90% of σ_0.2 and exposed to three environmental conditions, viz. deaerated pure water, aerated pure water, and aerated water containing 1.5 ppm of chloride ion. Pitting occurred in all environments but the density and depth of pits in the chloride-containing medium was markedly greater. No cracking was observed in deaerated pure water but cracks initiated in aerated water between 13 and 19 months and in less than 7 months in aerated 1.5 ppm Cl⁻ solution. The probability of a crack initiating from a pit of specific depth in aerated solution could be described well by a Weibull function. Profiling of pits and cracks in the disc steel tested in aerated 1.5 ppm Cl⁻ solution showed that there while there were many cracks with a depth greater than that of the corresponding pit the depth of some cracks was smaller than that of the corresponding pit, suggesting that cracks do not necessarily initiate from the bottom of the pits. The growth rate of short cracks emerging from pits appeared greater than that of long cracks in fracture mechanics specimens.     

X-ray structure analysis and elastic properties of a fabric reinforced carbon/carbon composite

The effect of heat treatment on microstructure of a plain-weave carbon fabric reinforced carbon-carbon composite with phenolformaldehyde-derived carbon matrix was investigated by X-ray diffraction. The diffraction patterns were analysed by the least-square fitting program Carbonxs. After heat treatment from 1000 to 2800 °C the interplanar distance of (002) planes decreased from 3.488 to 3.420 Å and the lattice parameter in basal plane increased from 2.440 to 2.464 Å, respectively. Simultaneously, the coherent block size in the basal plane directions increased from 18 to 54 Å, which was accompanied by an increase of the fraction of organised carbon atoms from 0.50 to 0.85. The 002 diffraction profile of the composite was much narrower than the sum of peaks of the matrix and fabric alone. This can probably be caused by a better crystallographic ordering (or by a partial graphitisation) of the matrix in the composite. On the other hand, the composite Young’s modulus slightly decreased with the treatment temperature increasing from 2200 to 2800 °C in spite of the established strong improvement of fibre crystallinity and, therefore, fibre modulus. The mechanisms diminishing the modulus of composite (e.g. partial matrix graphitisation at the fibre/matrix interface and decreasing fibre/matrix contact area) probably prevailed over the increasing contribution of the fibre modulus.     

Possible tactics to improve the growth of single-walled carbon nanotubes by chemical vapor deposition

The growth time, growth mode and the method of preparing the supported catalysts play an important role in the growth of single-walled nanotubes (SWNTs). Their effects on the chemical vapor deposition (CVD) growth of SWNTs with MgO-supported catalysts were investigated in this study. It is shown that the growth rate of SWNTs was large during the initial few minutes of growth, however the quality of the tubes was low owing to the formation of many defects. Long term growth may favor the formation of tubes with high quality and high yield, but the introduction of other forms of carbon (impurities) is also unavoidable. There was a balance between the increase in yield and quality and sacrifice of the purity during growth of SWNTs. MgO-supported catalysts prepared by the co-precipitation method were found to be more effective for the synthesis of SWNTs than those prepared by the widely used impregnation method. The size and dispersion state of the catalyst were found to be crucial in enhancing the growth of SWNTs. In addition, growth on the surface of SWNTs over nanosized catalyst films was shown to be more favorable for the synthesis of tube products with higher quality, yield and purity.