Comments on “Is the cause of size effect on structural strength fractal or energetic-statistical?” by Ba?ant & Yavari [Engng Fract Mech 2005;72:1-31]

Aim of this letter to the Editor is at replying to the criticisms raised by Ba?ant and Yavari [Ba?ant ZP, Yavari A. Is the cause of size effect on structural strength fractal or energetic - statistical? Engng Fract Mech 2005;72:1-31] against the fractal approach to the size-scale effects on the mechanical properties of materials and the concept of the Multi-Fractal Scaling Law presented by Carpinteri [Carpinteri A. Scaling laws and renormalization groups for strength and toughness of disordered materials. Int J Solids Struct 1994;31:291-302]. These criticisms will be analysed thoroughly, showing how they also contain some mistakes and misunderstandings. The presented elucidations should redirect the discussion to a more correct scientific debate.     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

VAc—BA／MMA三元共聚物的制备及产品的粘接强度和聚合方法的关系

本文介绍了ＶＡｃ／ＢＡ／ＭＭＡ三元共聚的两种方法，并通过实验证实：聚合方法对三元共聚物的粘接强度有明显的影响。     

Material removal and surface damage in EDM of Ti3SiC2 ceramic

Material removal and surface damage of Ti₃SiC₂ ceramic during electrical discharge machining (EDM) were investigated. Melting and decomposition were found to be the main material removal mechanisms during the machining process. Material removal rate was enhanced acceleratively with increasing discharge current, i_e, working voltage, u_i, but increased deceleratively with pulse duration, t_e. Microcracks in the surface and loose grains in the subsurface resulted from thermal shock were confirmed, and the surface damage in Ti₃SiC₂ ceramic led to a degradation of both strength and reliability.     

A parametric study of strength reduction factors for elasto-plastic oscillators

Strength reduction factors (SRFs) continue to play a key role in obtaining design forces from elastic design spectra (via response modification factors) in ductility-based earthquake-resistant design. Despite several years of sustained research efforts, it has not been conclusively shown how SRF for a given singledegree-of-freedom structural system depends on various source and site parameters. A parametric study is carried out here for the explicit dependence of SRF spectrum (describing variation of SRF with system period for a given ductility demand) on strong motion duration, earthquake magnitude, geological site conditions, and epicentral distance in case of (non-degrading) elasto-plastic oscillators. For this, scaled response spectra are considered for different combinations of earthquake magnitude, site conditions and epicentral distance, and SRF spectra are generated from 1274 accelerograms recorded in western USA after making those compatible with each of these spectra. It is shown that there is no clear and significant dependence of SRF spectrum on strong motion duration. Further, the parametric dependence on earthquake magnitude, site conditions, and epicentral distance broadly conforms to the trends reported by earlier investigations. In particular, this study confirms that the dependence of SRF spectra on earthquake magnitude should not be ignored. This paper has been contributed in honour of Professor R N Iyengar, Indian Institute of Science, on the occasion of his formal retirement.     

Analytical modeling and experimental study of tensile strength of asphalt concrete composite at low temperatures

In this study, analytical modeling of the tensile strength of hot-mix asphalt (HMA) mixtures at low temperatures was developed. To do this, HMA mixtures were treated as a two-phase composite material with aggregates (coarse and fine) dispersed in an asphalt mastic matrix. A two-phase composite model, which was similar to Papanicolaou and Bakos's [J. Reinforced Plast. Compos. 11 (1992) 104] model with a particle embedded in an infinite matrix, was proposed. Unlike Papanicolaou and Bakos's model, an axial stress was introduced to the fiber end to consider the load transferred from the asphalt mastic the aggregate. Efforts were also made to consider the effect of aggregate gradation, asphalt mastic degradation, and interfacial damage between the aggregates and asphalt mastic matrix on the tensile strength of the HMA mixtures. Experimental investigations were conducted to validate the developed theoretical relations. A reasonable agreement was found between the predicted tensile strength and the experimental results at low temperatures. Parameters affecting the tensile strength of asphalt mixtures were discussed based on the calculated results.     

适配器强度有限元分析

使用有限元程序ＳＡＰ５对某新型导弹发射筒内的适配器的强度进行了计算。通过结果分析，找出了适配器危险应力点的分布规律，它对结构选型设计具有指导意义。     

喷丸对连杆疲劳强度的影响

本文阐述了喷丸强化提高连杆表面质量和疲劳寿命。经喷丸处理,其试片弧高度迟到0.7mm时,疲劳极限提高了19%,达到440MPa,连杆实物疲劳强度试验结果表明,喷丸复盖率影响强化效果,文中还叙述了喷丸强化层应力分布的X射线应力测定工作。     

管线用高强韧性宽厚钢板的开发

本文回顾了舞钢高强韧性管线用宽厚钢板的研制开发过程，并结合生产工艺，对钢板性能作了全面分析，指导了钢管线钢的生产。舞钢X70级管线钢有较高的断裂韧性、良好的可焊性以及抗SSCC、HIC性能。舞钢正在进行技术改造，以进一步改善组织，提高性能、满足西气东输要求。