加氢裂化反应器新型冷氢箱的研究与工程设计

报道了加氢加化反应器新型旋流式冷氢箱的研究设计及实用效果，催化剂床层径向温差不大于5℃。     

Electron-Impact Cross Sections for Dipole- and Spin-Allowed Excitations of Hydrogen,Helium, and Lithium

Electron-impact excitation cross sections are presented for the dipole- and spin allowed transitions from the ground states to the np ²P states for hydrogen and lithium, and to the 1snp ¹P states for helium, n = 2 through 10. Two scaling formulas developed earlier by Kim [Phys. Rev. A 64, 032713 (2001)] for plane-wave Born cross sections are used. The scaled Born cross sections are in excellent agreement with available theoretical and experimental data.     

钛及钛合金中氧和氢的联合测定

叙述了用红外吸收法对钛及钛合金中氧和氢联合测定的方法，取得了测定的最佳条件。连续测定6次的相对标准偏差在10％以下，作加标回收试验的回收率为95．6％～103．9％。分析时间在3min以内，可应用于日常分析，结果满意。     

Procedure for Measuring Low Concentrations of H2 and H2S Above a Water Surface

A simple measuring procedure for low concentrations of H₂ and H₂S (at the level of ppm fractions) above the surface of water by using sensitive gas analyzers is suggested. The procedure is easily accomplished in conditions outside the laboratory (under field conditions).     

高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Adsorption and decomposition of H2S on Pd(1 1 1) surface: a first-principles study

Gradient-corrected density functional theory was used to investigate the adsorption of H₂S on Pd(1 1 1) surface. Molecular adsorption was found to be stable with H₂S binding preferentially at top sites. In addition, the adsorption of other S moieties (SH and S) was investigated. SH and S were found to be preferentially bind at the bridge and fcc sites, respectively. The reaction pathways and energy profiles for H₂S decomposition giving rise to adsorbed S and H were determined. Both H₂S_(ad) → SH_(ad) + H_(ad) and SH_(ad) → S_(ad) + H_(ad) reactions were found to have low barriers and high exothermicities. This reveals that the decomposition of H₂S on Pd(1 1 1) surface is a facile process.     

有机介质中合成二硫化钛

本文研究了硫化氢与四氯化钛在某些有机介质中的反应，并提出了一个合成二硫化钛的新方法。该法是将干燥的硫化氢通入沸腾的四氯化铁的α－氯代萘溶液中，使硫化氢和四氯化钛发生复分解反应而生成二硫化钛。方法简便易行。Ｘ－射线物相鉴定及化学分析结果表明，产物为单一物相的、符合化学计量的二硫化钛。     

熔敷金属扩散氢逸出特性研究

采用酒精法测量扩散氢 ,研究了焊条熔敷金属扩散氢含量以及在测氢过程中扩散氢逸出量与逸出时间的关系 (逸出特性 )。研究结果表明 ,熔敷金属扩散氢逸出特性受扩散氢含量、焊道数、熔敷金属化学成分和表面状态等多种因素的影响。熔敷金属扩散氢 (HDo)可以分为快速逸出扩散氢 (HDq)和慢速逸出扩散氢(HDs)两部分     

Inhibition of sulfide on the simultaneous removal of nitrate and p‐cresol by a denitrifying sludge

BACKGROUND: Many industrial discharges, such as those generated from petrochemical refineries, contain large amounts of sulfurous, nitrogenous and organic contaminants. Denitrification has emerged as a suitable technology for the simultaneous removal of these pollutants in a single reactor unit; however, more evidence is demanded to clarify the limitations of denitrification on the simultaneous removal of sulfide and phenolic contaminants and to optimize the biological process. The aim of this study was to evaluate the capacity of a denitrifying sludge to simultaneously convert sulfide and p‐cresol via denitrification. RESULTS: Sulfide was the preferred electron donor over p‐cresol, imposing a 5 h lag phase (required for complete sulfide removal) on organotrophic denitrification. Addition of sulfide (20 mg S^2? L^?1) to p‐cresol‐amended denitrifying cultures also decreased the reduction rate of nitrate and nitrite, as well as the production rate of nitrogen gas. Nitrite reduction rate was the most affected step by sulfide, decreasing from 35 to 21 mg N (g VSS d)^?1. A synergistic inhibitory effect of nitrate and sulfide was also observed on nitrite reduction. Despite the effects of sulfide on the respiratory rates monitored, complete removal of nitrate, sulfide and p‐cresol could be achieved after 48 h of incubation. CONCLUSION: Our results suggest that simultaneous removal of sulfide and p‐cresol could be achieved in denitrifying reactors, but a large hydraulic residence time may be required to sustain an efficient process due to inhibitory effects of sulfide. Copyright © 2008 Society of Chemical Industry     

纳秒级上升时间的高压脉冲群电源

按照IEC 61000-4-4/GB 17626.4—1998的要求，首先应用PSPICE仿真确定电路中各元件的参数值，然后基于拉普拉斯变换用MATLAB求解二阶电路验证各元件参数。在此基础上研制了一台以开关电源作为高压直流电源、以氢闸流管作为主控开关的脉冲群电源。该电源体积小、重量轻、效率高、成本低廉。试验结果表明，其输出信号符合标准要求，可用于快速瞬变脉冲群抗扰度试验。