ANALYTICAL SOLUTIONS FOR PEELING USING BEAM-ON-FOUNDATION MODEL AND COHESIVE ZONE

When fibrillation occurs during peeling, the normal stress in the adhesive may gradually reduce to zero at the peel front. The shear stress also reduces to zero. Classical beam-spring (or beam-on-elastic-foundation) models do not yield solutions that have these properties. With the use of a beam-on-foundation model combined with a cohesive zone in the neighborhood of the peel front, these properties can be satisfied. In order to obtain analytical solutions, peel tests are considered in which the backing has a small slope and is linearly elastic in the adhered region, and the traction law is assumed to be piecewise linear. Cases are considered with only normal stresses in the adhesive (mode I), only shear stresses (mode II), and both stresses coupled (mixed-mode behavior). Analytical solutions are obtained for displacements of the backing, forces in the backing, and stresses between the adhesive and the backing.     

加氢降凝组合工艺技术

抚顺石油化工研究院开发的生产低凝清洁柴油加氢降凝组合工艺,集加氢精制与临氢降凝工艺技术优点于一体,具有工艺流程简单、精制及降凝效果好、柴油收率高、原料适应能力强、产品方案灵活等特点,已在哈尔滨等炼油厂得到工业应用.     

N_2，H_2，Ar在正辛醇中高压溶解度的测定

测定了温度范围在０～４５℃，压力达到８４．６×１０￣５ｐａ时，Ｎ＿２，Ｈ＿２，Ａｒ在正辛醇中的７５点高压气体溶解度数据，并提出一个由高压实验数据回归常压溶解度的方法。     

高压蒸汽管道保温研究

计算了不同管径和保温厚度下蒸汽管道输送高压蒸汽的热损失和温度降。结果表明:保温厚度越大,蒸汽的热损失越小、温度降越小;保温材料导热系数与蒸汽的热损失呈正比;环境温度越高,蒸汽的热损失越小;环境风速对热损失的影响不大。同时研究了保温材料选择和保温结构对节能的影响。     

Enhancement of radiation‐resistant effect in ethylene–vinyl acetate copolymers by the formation of ethylene–vinyl acetate copolymers/clay nanocomposites

Ethylene–vinyl acetate (EVA) copolymers/clay nanocomposites, prepared by using nonreactive organophilic clay and reactive organophilic clay, were characterized by X‐ray diffraction and by high‐resolution transmission electron microscopy. The influence of gamma irradiation on the structure and properties of the pure EVA and EVA/clay nanocomposites was systematically investigated. In the presence of gamma radiation, the clay can effectively restrain the increase of the storage modulus of EVA/clay nanocomposites, which was supported by dynamical mechanical analysis. Gamma irradiation had almost no effect on the thermal properties of EVA/clay nanocomposites by using nonreactive organophilic clay, but it obviously improved the thermal stability of EVA/clay nanocomposites by using reactive organophilic clay. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2532–2538, 2005     

Operation of a catalytic reverse flow reactor for the purification of air contaminated with volatile organic compounds

Catalytic oxidation in a reverse flow reactor is an attractive process for the decontamination of air polluted with volatile organic compounds (VOCs). In this paper several aspects of operating this type of reactor for air purification under strongly varying conditions will be discussed. For a successfit operation of such reactor a minimum amount of combustibles is required, and a simple theory is developed to predict this minimum value. This minimum amount is strongly influenced by the reaction kinetics, the heat transport in the packed bed and the adiabaticity of the reactor. To cope with a too low temperature level in the reactor for a complete conversion, an electrical heating device should be installed in the centre of the reactor bed to increase locally the temperature rapidly and efficiently. To control the maximum temperature in case of too high concentrations, extra air should be added to the feed.     

网络控制系统随机延迟的预测控制

针对网络控制系统随机时延、时变等特性造成控制效果不理想的问题,提出一种改进的广义预测控制与递推最小二乘法相结合的预测控制策略.上述控制策略将传统的预测控制运用于网络控制系统中,针对网络随机时延的特性,采用改进的广义预测控制算法对随机时延进行补偿.结合分段可变遗忘因子递推最小二乘法对被控对象模型参数进行在线辨识,可以减少网络控制系统参数突变对系统造成的不利影响.仿真结果表明,所提出的预测控制策略可以有效解决网络控制系统随机时延问题,并且在参数突变的情况下也能够获得良好的控制效果.     

精密金属焊接坏点的视觉识别方法研究与仿真

研究高精密金属焊接坏点准确视觉识别的问题.由于高精密金属焊接坏点的颜色特征与金属本身特征相似,而在坏点很小并且与外部环境过于类似的干扰下,传统的基于像素差异的识别结果不精确,一旦焊接坏点分布的过于集中,干扰将更大,导致焊接坏点识别准确性降低.为解决上述问题,提出一种新的计算机视觉的高精密金属焊接坏点识别方法.采集高精密金属焊接坏点计算机视觉图像,针对金属图像进行特征提取,并对提取的特征进行离散小波变换处理,获取增强处理后的视觉图像.根据增强处理后的视觉图像特征值,获取高精密金属焊接坏点的分布密度,计算焊接坏点的空间位置,实现高精密金属焊接坏点识别.实验结果表明,利用改进算法进行高精密金属焊接坏点识别,能够提高识别的准确率,并且获取焊接坏点在高精密金属制品中的分布位置,为高精密金属制品的生产质量提供保障.     

基于视觉辅助的汽车转向路感优化控制仿真

汽车行驶速度过快的情况下,与路面的冲击反力会瞬间增大.路感控制过程需要迅速改变硬件结构参数以保持稳定,过大变化使得控制过程出现异动,导致汽车转向路感系统出现“打手”(过控制)问题,传统的路感系统控制方法针对过控制问题,需要动态变化控制参数,使其与过控制过程形成匹配,但是传统方法很容易引起模型不稳,导致对汽车转向路感系统的控制误差增大.提出视觉辅助的汽车转向路感系统快速控制方法,采用Harris角点控制算法获取监控视频中每幅汽车转向路感图像中的角点位置,对每帧汽车转向图像的角点进行LK光流场运算,依据运动目标的光流连续性获取可能的目标角点信息,通过聚类分析对若干角点位置集进行数字运动汽车转向图像处理中的形态学处理,得到汽车当前所处的实际位置,实现汽车转向路感系统的快速控制.实验结果证明,改进种方法的可行性,并且具有较高的控制精度.     

塑料异型材挤出模中的压力分布

本文对塑料异型材挤出模机头典型流道结构进行了分析，给出了各种类型流道的压力降计算公式，并用一实例说明文中所述方法的正确性。