冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

TP130TT高抗挤套管研究与应用

为了提高盐层段固井质量 ,中原油田研究开发了 TP130 TT高抗挤套管 ,性能试验评价表明 ,其抗挤强度超过 16 0 MPa,并给出了其固井质量评价标准。在中原油 346口井中的应用表明 ,该套管有效地解决了盐层段套管损坏问题 ,延长了油气水井寿命 ,经济效益和社会效益显著。     

Empirical comparison of image retrieval color similarity methods with human judgment

It is important to verify assumptions and methods of image retrieval against actual human behavior. A study was conducted to compare similarity methods of color histograms against human assessment of similarity. The similarity methods tested include basic histogram intersection, center histogram matching, locality histogram matching, and size-weighted histogram matching. 161 subjects participated in the empirical study. The findings, based on Spearman correlation analysis, showed that both the basic histogram intersection method and size-weighted histogram are very close to human assessment of similarity (Spearman correlation coefficient of 0.915). The other two are not close to human judgment on similarity. This study illustrates an alternative approach to evaluating matching algorithms. Unlike the usual measures of recall and precision, this approach emphasizes human validation. Fewer images are required with the use of statistical testing.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Concurrent effect of microporosity and chemical structure on the equilibrium sorption properties of cellulose-based hydrogels

Polyelectrolite hydrogels are crosslinked polymers which display high sorption capacity in water and water solutions. They are widely used in the marked of personal hygiene products, as well as in other biomedical and industrial applications. In the most industrial application they are not biodegradable and prepared starting from acrylamide.In this work, the chemical-physical analysis of a novel class of natural polymers-based microporous superabsorbent hydrogels has been presented. The main focus is the definition of the relationship between material's chemical-physical structure and its equilibrium sorption properties.The effect of the variation of the degree of crosslinking, the polyelectrolyte nature of the backbone and the hydrogel microporosity on its swelling properties has been analysed, and a good agreement with the theoretical statements has been displayed.The effect of the ionic strength and the pH of the external solution in contact with the hydrogel on its equilibrium sorption properties has also been assessed, and an high sensitivity to these variations was detected for all the tested chemical compositions and physical structures.This work have to be considered part of the efforts towards the reduction of the environmental impact of the large scale consumption industrial polymer based products.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

影响混凝土强度的因素及控制措施

分析了水泥强度等级、水灰比和骨料质量等内因,及施工条件、养护温度、湿度、龄期等外因对混凝土强度的影响,并提出了控制混凝土强度的相应措施,以确保混凝土强度符合设计及施工要求,从而保证建筑物结构安全。     

A simple approximation algorithm for the weighted matching problem

We present a linear time approximation algorithm with a performance ratio of 1/2 for finding a maximum weight matching in an arbitrary graph. Such a result is already known and is due to Preis [STACS'99, Lecture Notes in Comput. Sci., Vol. 1563, 1999, pp. 259-269]. Our algorithm uses a new approach which is much simpler than the one given by Preis and needs no amortized analysis for its running time.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.