我国城镇住宅节地措施研究简

在城镇化的发展过程当中,城市土地价值越来越高,如何通过研究住宅的发展来节约土地资源变得尤为重要.笔者通过对城镇住宅节地措施的研究,分析发展节地住宅环境,希望能对我国节约城镇土地有所帮助.     

TC10钛合金相变点的测定

分别用计算法、热膨胀法和连续升温金相法测定了TC10钛合金的β相转变温度.结果表明,计算法得到该合金相变点温度为936℃,热膨胀法测得该合金相变点温度为939.6℃,连续升温金相法测得该合金相变点温度为937.5℃.3种方法测得的结果相当接近,说明这3种方法可以相互结合使用.     

微波加热法合成蜂窝状堇青石载体Al2O3涂层

采用微波加热法在堇青石蜂窝陶瓷基体表面涂覆多孔Al2O3涂层,研究了制备条件对堇青石蜂窝陶瓷表面Al2O3涂层中Al2O3的质量分数的影响。通过BET、SEM对涂层结构及形貌进行了表征,结果表明,采用微波加热法制备的Al2O3涂层均匀、稳定,具有较大的比表面积、孔容和较高的Al2O3质量分数。     

基于短时间温升试验和参数估计模型预测稳定温度

电机在稳定运行状态下的绕组温度是反映电机性能的重要参数。通常,检测机构依据GB/T1032-2012中规定的方法进行温升试验,至少需要持续3小时,甚至达到6小时。短时间内求取电机稳定温度能够提升检测机构温升检测试验的效率,节约检测机构大量的电力成本和人工成本。同时,根据预测温度能够监测绕组温度,避免绕组的绝缘漆损坏而导致电机烧毁。通过研究均匀纯铜的指数发热规律、创新实时带电测量绕组温度的装置和基于线性逼近方式建立参数估计模型的方法,搭建了在短时间高精度预估电机温度的系统。在对不同功率段电机进行现场温升实验验证中,结果表明系统能够高效准确的预测电机的稳定温度。     

长轴类零件整体中频同时加热淬火的试验和应用

对长轴类零件采用大功率中频机同时加热表面淬火的方法，配以专用感应圈和伸缩应圈的应用和自回火的应用，结果表明，可提高零件中频表面淬火质量，并大大提高生产效率，从而使企业在生产中取得高产品质量，高生产效率和低生产成本的极佳效果。     

热力管线中不锈钢波纹管破裂原因分析

采用金相显微镜和扫描电镜分析了热力管线中不锈钢 波纹管破裂原因.该波纹管破裂特征与一般环向开裂不同，裂纹沿轴向扩展.分析认为，破裂 属穿晶应力腐蚀.引起应力腐蚀的介质是土壤中的氯化物，而应力则来自环向工作应力和冷 加工残余应力，而环向工作应力起主导作用。     

水玻璃加入量对微波硬化砂强度及溃散性影响的试验研究

采用微波加热技术来加热硬化水玻璃砂,对比分析了水玻璃的加入量对砂型试样抗拉强度和残留强度的影响规律。试验结果表明,在539W微波功率加热条件下,水玻璃砂的抗拉强度随着水玻璃加入量的增加而强度上升;在相同微波加热条件下,水玻璃砂的残留强度也随着水玻璃加入量的增多而增大。     

The Microstructure and Mechanical Properties of the Low Carbon Microalloy Steel by High Voltage Electropulse Heating

The low carbon microalloy steel samples were heated to different temperatures by high voltage electropulse discharge heating method. The temperature of sample increases with the discharge current density. Microstructures were observed by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results show that coexist microstructure of ultrafine ferrite grain and martensite can be obtained by proper high voltage electropulse discharge heating process parameter. The tensile testing indicate that better mechanical properties were obtained, including 758MPa yield strength, 796MPa ultimate strength and 12% total elongation.     

Advances in fabricating superplastically formed and diffusion bonded components for aerospace structures

Superplastic forming and diffusion bonding (SPF/DB) production hardware is being fabricated today for aerospace applications. Metal tooling is being used to bring the titanium sheets into contact so diffusion bonding can occur. However, due to material sheet and tooling tolerances, good bond quality is difficult to achieve over large areas. A better method for achieving DB is to use “stop-off” inside sealed sheets of titanium, which constitutes a pack, and then the pack is bonded using external gas pressure. A good method for heating the pack for this process is to use induction heating. Components using “stop-off” that were diffusion bonded first and then superplastically formed have shown much better bond quality than components that were produced using matched metal tooling. This type of tooling has been successful at bonding small areas as long as the exerted pressure is concentrated on the area where bonding is required. Finite element modeling is providing weight effect solutions for titanium SPF/DB aerospace structures. This paper was presented at the International Symposium on Superplasticity and Superplastic Forming, sponsored by the Manufacturing Critical Sector at the ASM International AeroMat 2004 Conference and Exposition, June 8–9, 2004, in Seattle, WA. The symposium was organized by Daniel G. Sanders, The Boeing Company.     

研究Nd-Fe-B粉末材料中不同状态氧的新方法

基于不同氧化物与碳的结合能不同,与碳的还原反应在不同的分析条件下具有先后次序,用脉冲红外氧化物夹杂分析仪,对4μm的烧结Nd Fe B永磁材料粉末的氧化行为进行了方法研究。实验结果表明,通过合理设置参数,选用跟踪升温模式,可以快速分离Nd Fe B永磁材料粉末中的不同氧化物,并可以通过加权方法进行定性验证。