功率器件封装工艺中的铝条带键合技术

文章回顾了功率器件封装工艺中几种常见的互连方式,主要介绍了铝条带键合技术在功率器件封装工艺中的主要优点,特别是它应用在小封装尺寸的功率器件中。铝条带的几何形状在一定程度上降低了它在水平方向的灵活性,但却增加了它在垂直方向上的灵活性。铝条带垂直方向的灵活性可以让我们使用最少的铝条带条数来达到功率器件键合的要求。也由于几何形状的不同,铝条带键合具有一些不同于铝线键合的特点,但它对粘片工艺、引线框架和包封工艺的要求与粗铝线键合极其相似,可以与现有的粗铝线键合工艺相兼容,不需要工艺和封装形式的重新设计。     

楔横轧工艺在双头呆扳手制坯上的应用

介绍了楔横轧成形工艺及其在双头呆扳手制坯上的应用，阐明了楔横轧模具的主要设计参数。通过双头呆扳手制坯工艺的实践，对新旧制坯工艺的技术经济进行了分析与比较，证明了楔横轧工艺的一系列优点     

发电机用磁性槽楔对电磁参数与性能的影响

以一台1MW隐极同步发电机为例建立数学模型,通过理论计算与有限元软件分析该电机采用不同相对磁导率的磁性槽楔时,对发电机的电磁参数与电机性能的影响。结果表明装有磁性槽楔的电机要比非磁性槽楔的电机气隙系数减小,气隙磁密波形更平滑,输出电压波形质量更好,励磁电流降低,但短路比减小,以及磁导率越大磁性槽楔所受电磁力越大。综合确定磁性槽楔选用相对磁导率为5的更为合理。     

Heat transfer enhancement in hydromagnetic dissipative flow past a moving wedge suspended by H2O-aluminum alloy nanoparticles in the presence of thermal radiation

This letter investigates the two dimensional magnetohydrodynamic Falkner Skan flow of water saturated with AA7072–H₂O and AA7075–H₂O nanoparticles over a moving wedge. Influence of viscous dissipation and thermal radiation is also under consideration. The model is reduced into nondimensional form by using defined self-similar transformations. Then, numerical study (Runge-Kutta numerical scheme) is carried out for solution purpose. The effects of pertinent flow parameters are discussed in the flow regimes by means of graphical aid. Graphical results for special cases (static wedge and when the movement of flow and wedge is in opposite direction) of the model are also elucidated graphically. It is noted that fluid velocity decreases for volumetric fraction and magnetic force favor the velocity. Significant effects of thermal radiation and nanoparticles volume fraction pointed for thermal filed and the influence of Eckert number is almost inconsequential. For more radiative fluid heat transfer coefficient decreases and nanoparticles volumetric fraction favor the local rate of heat transfer. In the presence of AA7075 nanoparticles, rate of heat transfer is quite rapid as compared to that of AA7072 nanoparticles. To validate the present computations, some present results are compared with already existing results in the literature and found better agreement between them. Finally, major points of the study ingrained in the last section of the letter.     

某水电站进水口右岸楔形体边坡稳定性分析

针对西藏地区水电工程前期设计阶段受地质资料限制,对楔形体边坡稳定性分析往往需要大量试算验算,设计工作效率低的问题,以某水电站坝址楔形体XT2为分析对象,采用数值计算软件ABAQUS对初始地应力场进行反演,并将反演出的地应力场应用于大型有限差分分析软件FLAC3d,进行楔形体边坡稳定性计算与分析。结果表明,该方法既保证了计算结果的可靠性,又大大缩短了计算时间。     

热轧带钢局部高点的原因分析及改进措施

对热轧带钢在冷轧时产生局部高点的原因进行了分析,并提出了相应的改进措施.改进后,精轧机的轧辊磨损量减少了约120～150μm,不均匀磨损减少了40～60μm,从而解决了冷轧料局部高点问题.     

Dislocation emission criterion for a wedge crack under mixed mode loading

Dislocation emission criterion for a wedge crack under mixed mode loading was investigated using Airy stress function. The order of singularity at the wedge crack tip due to remote loading was found to vary with the loading mode. The plastic zones for plane stress and plane strain were studied based on von Mises' and Tresca criteria. The dislocation emission criterion was examined for both loading modes. The mechanism of crack propagation was believed to be controlled by dislocation emission. Under an action of Mode I loading, the wedge tip movement occurred when a pair of edge dislocations of Burgers vectors be ⁱ and –be ^–i were emitted from the wedge tip where b and were the magnitude of Burgers vector and the angle between the positive x axis and the line connecting from the tip to dislocation. Similarly, under an action of Mode II loading, the wedge crack tip moved as soon as either an edge dislocation of Burgers vector along the x direction was emitted from its tip or a pair of edge dislocations of Burgers vectors be ⁱ and be ^–i were emitted from the wedge tip. The conventional mechanism of crack propagation based on the energy release rate was not expected to occur. The calculated results for a few special cases were presented and compared with those reported in the literature.     

Torsional load transfer from a rigid shaft to an elastic plane with a slit

A plane elastostatic problem for an elastic wedge loaded by a concentrated moment at its apex provides an example of violation of the Saint-Venant principle for apex angles 2 larger than . Considering the problem for a truncated wedge, Neuber demonstrated the method of construction of an applicable solution for any apex angles in the range 22, despite the failure of the Saint-Venant principle. In the present paper the particularly important case of the truncated-wedge problem is examined. The truncated wedge degenerates into a slitted elastic plane, while a rigid circular shaft, acted upon by a torsional moment, is inserted into the plane. The analytical solution of the mixed boundary-value problem is obtained. Numerical results turn out to be in complete agreement with Neuber's results for the slitted elastic plane.     

DEFORM-3D在楔横轧成形模拟中的应用

介绍了有限元分析软件DEFORM-3D及其模块结构,并通过楔横轧成形实例分析介绍了该软件在网格划分、应力和应变分析、温度分析、点的跟踪、载荷分析等方面的典型应用。     

鲤鱼钳毛坯楔横轧成形压力的工程计算

介绍了楔横轧成形过程的工艺参数及变形区参数，分析了楔横轧展宽区的金属变形情况及推导了变形区参数的工程计算公式。文末对鲤鱼钳毛坯进行了实例计算。