Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

65 Mn热轧带钢表面裂纹分析

分析了热轧带钢表面裂纹产生的原因，介绍了采取的工艺措施及其效果。     

基于高抗热震性能的陶瓷刀具材料的微观结构设计

本文以现有的抗热震断裂和抗热震损伤的评价理论为基础，通过对材料中微裂纹的长度进行预测，从而实现了对陶瓷刀具材料的抗热震性能的微观结构设计。根据此理论对现有材料的抗热震性能的进行预测，预测结果与实际的测量结果相符，验证了该理论的正确性。     

Characterization of Ceramic Composite-Membranes Prepared by ORMOSIL Coating Sol

Sol-gel methods offer many advantages over conventional slip-casting, including the ability to produce ceramic membranes. They are purer, more homogeneous, more reactive and contain a wider variety of compositions. We produced ormosil sol using sol-gel process under different molecular weight of polymer species [polyethylene glycol (PEG) ] in total system [Tetraethyl ortho silicate(TEOS)-polyethylene glycol (PEG)]. The properties of as-prepared ormosil sol such as,viscosity, gelation time were characterized. Also, the ceramic membrane was prepared by dip-coating with synthetic sol and its micro-structure was observed by scanning electron microscopy. The permeability and rejection efficiency of membrane for oil/water emulsion were evaluated as cross-flow apparatus. The ormosil sol coated Membrane is easily formed by steric effect of polymer and it improves flux efficiency because infiltration into porous support decreased. Its flux efficiency is elevated about 200(1/m2·h) compared with colloidal sol coated membrane at point of five minutes from starting test.     

Failure of a stationary pump engine piston

Piston failures are not a common occurrence, but they do occur, and failure is usually associated with fatigue crack growth. Most failures initiate at the gudgeon pin hole or in the skirt of the piston. Occasionally they fail elsewhere. In the example covered in this paper, failure initiated in the crown and progressed down to the gudgeon pin before final failure occurred. This paper outlines the cause and mode of failure and shows that small metallurgical discontinuities can contribute to these failures under the right circumstances.     

The wheel–rail interface—some recent accidents

The importance of the wheel–rail interface to the safe operation of railways is discussed. Some aspects of the history of rails and wheels are introduced. Several recent accidents involving the wheel–rail interface are described. The great importance of operating both vehicles and track as a system is emphasized, together with the necessity of maintaining both in good condition.     

Evaluation of Slow Crack Growth Resistance in Ceramics for High-Temperature Applications

The slow (subcritical) crack growth (SCG) resistance of Si₃N₄ and SiC ceramics has been evaluated by a stepwise loading test on bending bars precracked by Vickers indentation. Three highly refractory materials were selected for the evaluation: i.e., (1) high-purity Si₃N₄ sintered by hot isostatic pressing (HIP) without additives and (2,3) α - and β - SiC pressureless sintered with B and C addition. Under the hypothesis of linear elastic behavior at high temperature, which was found satisfied in the present materials, the SCG resistance was expressed in terms of initial stress intensity factor critical for SCG failure within a predetermined lifetime. The present method was found useful in shortening the testing time and consistent with other traditional fatigue tests (e.g., static-fatigue test): It is recommended as a screening test for materials under research and development. Among the materials tested in the present study, the highest SCG resistance up to 1440°C was found in the high-purity Si₃N₄ without additives.     

Numerical modelling for scattering of waves in three-dimensional cracked material

In this paper, a mathematical model is proposed for the problem of the scattering of plane waves in a three-dimensional cracked materials. Instead of obtaining closed-form solutions as in conventional theoretical analysis methods, this approach, called the Equivalent Nodal Force (ENF) method formulates the mechanical effects of cracks as an equivalent nodal force in a numerical procedure, and physically translates cracked material into an equivalent continuous one. Several mechanical relations between waves and cracks are evident from this method. Also the results of several numerical calculations are presented and these are compared with those obtained by the conventional methods.