一个用户接口管理系统

本文介绍了一个用户接口管理系统NUUIMS的设计和实现.重点叙述了该系统基于规范化目标用户接口模型的设计思想,系统组成及描述方法.文章也讨论了使用NUUIMS设计而成的用户接口的特点.     

方圆坯铸机开发新断面自动化程序的实现

文章介绍了包钢连铸机结晶器液位、喷淋水、热坯压力等主要参数实现自动控制的过程,阐述了上述参数如何根据不同铸坯断面而改变,并针对钢厂开发新断面如何实现参数的切换提出解决办法.     

浅谈炼钢车间的自动控制系统

介绍了天津钢铁工业结构调整改造后的新钢铁企业炼钢车间的自动控制系统，系统的配置、主要功能，并对系统做出评价。     

基于SDL的通信软件维护模型SMM

软件维护是软件生存周期的一个重要且花费很大的阶段，维护工作的自动化是软件行业十分迫切的需要。本文提出了一个基于ＩＴＵ－ＴＳＤＬ语言的通信软件维护模型ＳＭＭ。在此模型中，软件维护被分成三个部分：建立面向维护的数据库，制定维护规范和基于功能转换的自动维护。该模型将有助于软件维护支撑环境的建立     

A Low-Power Wide-Dynamic-Range Analog VLSI Cochlea

Low-power wide-dynamic-range systems are extremely hard to build. The biological cochlea is one of the most awesome examples of such a system: It can sense sounds over 12 orders of magnitude in intensity, with an estimated power dissipation of only a few tens of microwatts. In this paper, we describe an analog electronic cochlea that processes sounds over 6 orders of magnitude in intensity, and that dissipates 0.5 mW. This 117-stage, 100 Hz to 10 KHz cochlea has the widest dynamic range of any artificial cochlea built to date. The wide dynamic range is attained through the use of a wide-linear-range transconductance amplifier, of a low-noise filter topology, of dynamic gain control (AGC) at each cochlear stage, and of an architecture that we refer to as overlapping cochlear cascades. The operation of the cochlea is made robust through the use of automatic offset-compensation circuitry. A BiCMOS circuit approach helps us to attain nearly scale-invariant behavior and good matching at all frequencies. The synthesis and analysis of our artificial cochlea yields insight into why the human cochlea uses an active traveling-wave mechanism to sense sounds, instead of using bandpass filters. The low power, wide dynamic range, and biological realism make our cochlea well suited as a front end for cochlear implants.     

起重机吊钩拖动绕线电动机他励双高调速系统

本文提出励磁电流可自动控制的他励式双高调速系统设计方案。系统在提升特别是在下放重物时，具有较硬的机械性；在负载１０－１００％的变化范围内，可实现最大偏差Δｎｍａｘ／ｎｍｉｎ１００％≤１０％，调速范围Ｄ≥１０；在满载运行条件下，可节约电能８０％以上。     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

潜油电动机滑行时间的自动测量

潜油电动机滑行时间是评定电动机装配质量的重要指标。鉴于手工测量电动机滑行时间存在效率低和误差较大的不足,设计了潜油电动机滑行时间自动测量系统。它通过分压电路和计算机自动测量系统测量潜油电动机定子上感应的电压变化状况,即可得到电动机滑行时间。用手工测量、波形分析和自动测量3种方法测量6种型号电动机的滑行时间,其中5种滑行时间长于3s,判定为合格;1种滑行时间短于3s,判定为不合格。3种方式测量的滑行时间具有较好的一致性,仅波形分析法得出的滑行时间比自动测量的滑行时间稍长,表明自动测量方法的精度和重复性可满足要求。     

引黄五座泵站火灾自动报警及联动控制系统

介绍了引黄工程五座泵站的火灾自动报警系统的组成及功能，对泵站的火灾探测系统、报警系统、联动控制系统、灭火系统、控制台等原理进行了详细说明，供同行参考借鉴。     

双辊薄带钢连铸在线自动检测系统

介绍了双辊薄带钢连铸工艺,设计了双辊连铸机的计算机在线自动检测系统,通过采取正确的抗干扰措施提高了检测的精度,系统在双辊薄带钢连铸试验中应用效果良好.