全文获取类型
收费全文 | 1596篇 |
免费 | 164篇 |
国内免费 | 60篇 |
学科分类
工业技术 | 1820篇 |
出版年
2024年 | 7篇 |
2023年 | 49篇 |
2022年 | 44篇 |
2021年 | 45篇 |
2020年 | 32篇 |
2019年 | 51篇 |
2018年 | 27篇 |
2017年 | 37篇 |
2016年 | 37篇 |
2015年 | 47篇 |
2014年 | 103篇 |
2013年 | 64篇 |
2012年 | 89篇 |
2011年 | 79篇 |
2010年 | 64篇 |
2009年 | 91篇 |
2008年 | 59篇 |
2007年 | 76篇 |
2006年 | 99篇 |
2005年 | 78篇 |
2004年 | 63篇 |
2003年 | 82篇 |
2002年 | 53篇 |
2001年 | 62篇 |
2000年 | 50篇 |
1999年 | 30篇 |
1998年 | 41篇 |
1997年 | 49篇 |
1996年 | 27篇 |
1995年 | 46篇 |
1994年 | 33篇 |
1993年 | 18篇 |
1992年 | 25篇 |
1991年 | 22篇 |
1990年 | 18篇 |
1989年 | 16篇 |
1988年 | 5篇 |
1987年 | 1篇 |
1983年 | 1篇 |
排序方式: 共有1820条查询结果,搜索用时 15 毫秒
21.
22.
23.
24.
25.
首先简要介绍了交流电源的电流衰减方式;其次讲述了交流方波TIG焊机的特点、工作原理以及工作波形;最后详细介绍了脉冲TIG焊的主要特征、原理以及焊接时的工艺参数,并例举了不锈钢、钛合金、铝合金焊接时的工艺参数选择范围。 相似文献
26.
Microstructure and mechanical properties of wrought magnesium alloy AZ31B welded by laser-TIG hybrid 总被引:5,自引:0,他引:5
The laser-TIG hybrid welding was mainly used to weld the wrought magnesium alloy AZ31B. The tech-nical characteristics of laser-TIG hybrid welding process was investigated and the interactional mechanism between laser and arc was discussed, at the same time the microstructure and mechanical properties of the wrought magnesi-um alloy AZ31B using laser-TIG hybrid welding were analyzed by optical microscope, EPMA, SEM, tensile ma-chine, hardness machine. The experimental results show that the presence of laser beam boosts up the stability of the arc during high speed welding and augments the penetration of weld; the crystal grains of magnesium alloy weld are fine without porosity and cracks in the best welding criterion and the microstructure of HAZ does not become coarse obviously. The elements profile analysis reveals that Mg content in the weld is lower than that of the base metal, but Al content is higher slightly. Under this experimental condition, the wrought magnesium alloy AZ31B joint can be achieved using laser-TIG hybrid process and the tensile strength of the joint is equivalent to that of the base metal. 相似文献
27.
用热丝化学气相沉积法(HFCVD)在蓝宝石基片上原位制备了MgB2超导薄膜,并用XRD、SEM和dc SQUIDs研究了基片温度和时间对薄膜相组成、表面形貌和超导临界转变温度Tc的影响.结果表明,HFCVD原位生长MgB2薄膜可以抑制MgO杂质的生成.基片温度在500℃以下,MgB4杂相容易出现;在500℃以上时,可以消除MgB4杂相;在600℃时,获得了纯单相的MgB2薄膜,其超导临界转变温度达到36 K.随基片温度升高,薄膜结晶性、致密度和超导临界转变温度提高. 相似文献
28.
使用自制的含Sc、Ce、Be的TiB2原位增强与4047焊丝为填充材料对T6态SiCp/AlMMCs 进行TIG焊,对接头的力学性能、显微组织以及断口形貌和第二相粒子进行分析。结果表明:两种焊丝焊接该种材料的焊缝成型优良,4047焊丝成型更加美观;TiB2接头的抗拉强度明显优于ER4047接头,平均强度达到171.88MPa,相对于4047接头强度提高40.03%,TiB2粒子起到了原位增强的作用;两种接头的硬度值在焊缝中心近似呈对称分布,焊缝区硬度最低,平均值分别为:71.65HV、60.02HV,热影响区硬度的“过时效”现象明显;焊缝中SiC颗粒较少,存在严重贫瘠区 ,未发现明显的Al4C3脆性物;显微组织都为枝晶组织,但4047接头焊缝枝晶粗大,TiB2接头焊缝晶粒细小,稀土元素Sc、Ce、Be起到了细化晶粒的作用,且TiB2粒子在焊缝中分布均匀;TiB2接头断口中气孔较少,为韧-脆性混合性断裂,韧窝中第二相粒子较多;4047接头断口中气孔较多,为韧性断裂,韧窝中第二相粒子较少。 相似文献
29.
超薄奥氏体不锈钢TIG焊 总被引:1,自引:2,他引:1
超薄奥氏体不锈钢TIG焊姜劲松(江苏省南通市工业设备安装公司226008)随着我国经济的迅速发展,在建筑装璜业、广告业、生活用品制造业等行业大量采用了超薄型不锈钢材料(壁厚0.3~1.0mm),一般为0Cr18Ni9Ti。奥氏体不锈钢焊接性良好,但因... 相似文献
30.