Influence of alloy ingredients on mechanical properties of ternary boride hard alloy clad materials

Using Mo, B-Fe alloy and Fe powders as raw materials, and adding C, Cr and Ni ingredients, respectively, or C, Cr and Ni mixed powders, ternary boride hard alloy clad materials was prepared on Q235 steel substrate by means of in-situ reaction and vacuum liquid phase sintering technology. The influence of alloy ingredients on the mechanical properties of ternary boride hard alloy clad materials was investigated. The results indicate that a mixture of 0.8% C, 5% Cr and 2% Ni ingredients gives a ternary boride hard alloy clad material with optimal mechanical properties, such as high transverse rupture strength, high hardness and good wear resistance.     

550 MPa级中厚板矫直过程中表面凹坑缺陷的成因与对策

针对550 MPa级高强中厚板在矫直过程中极易出现氧化铁皮压入凹坑缺陷的问题，根据现场矫直工艺，研究了在不同温度下进行热变形时试样表面和横截面的形貌，钢基体与氧化铁皮界面处平直度的变化规律。结果表明，热变形温度为450 ℃时，表面氧化铁皮开始出现裂纹，且随着变形温度的降低，裂纹的数量逐渐增加；此外，氧化铁皮与钢基体之间的界面长度随变形温度的降低而呈直线增加，表明氧化铁皮与钢基体界面平直度随着热变形温度的降低越发粗糙、易脱落而形成凹坑缺陷。为此，应适当提高终轧温度以确保矫直时钢板表面温度大于450 ℃，同时提高钢板的运行速率，防止氧化铁皮在低温变形发生破碎和脱落的同时降低氧化铁皮厚度，从而减小因氧化铁皮脱落而造成凹坑缺陷的发生几率。     

高纯Fe中氢损伤规律的研究

本文采用正电子湮没技术研究了高纯Fe中的氢损伤规律,实验结果表明,在0.5mol/L H_2SO_4溶液中不加毒化剂电解充氢时,产生氢损伤的临界电流密度为20 mA/cm~2;而在0.5mol/L H_2SO_4溶液中加少量As_2O_3作为毒化剂电解充氢时,即使很小的电流密度也会产生氢损伤,配合慢拉伸试验,还发现试样内部产生氢损伤以后,它将控制随后的形变和断裂过程     

Net shape formation of sub-micron alumina with reduced flaws by high-speed centrifugal compaction process

A new compacting method for powder materials is presented. High-Speed Centrifugal Compaction Process (HCP) utilizes centrifugal force of about 10,000 g for the compaction. HCP is suitable for net shape compaction of fine sub-micron and nano-powders. HCP possesses a unique compacting mechanism that is different from other colloidal processes including Pressure Casting (PC), and has a number of useful characteristics. HCP has a higher compacting speed than PC, wide applicability for net shape formation, as well as a defect removing function. Because of homogeneous and flawless green microstructure, HCP alumina shows superior sinterability and higher strength and hardness than most of other aluminas. This article is based on a presentation made in the symposium “The 3rd KIM-JIM Joint Symposium on Advanced Powder Materials“, held at Korea University, Seoul, Korea, October 26–27, 2001 under auspices of The Korean Institute of Metals and Materials and The Japan Institute of Metals.     

涡流检测技术在宝钢热轧轧辊上的应用

介绍了轧辊涡流检测仪的工作要求、设备组成和使用方法,指出对轧辊进行涡流检测可防止爆辊,减少轧辊磨削量。     

冷轧处理线卷取机带头定位精度的改进

针对采用带头与卷取机芯轴橡胶套筒定位区动态接触的传统自动定位技术控制效果不好而带来带头印缺陷的问题，对其产生原因进行了分析，这是因为不同规格、钢种带钢的工艺参数不同，带钢穿带过程中在传送辊上的打滑量不同，在传输通道上的下垂量不同，带头到达卷取机芯轴定位区时计算带头位置与实际带头位置存在不稳定的偏差，因此带头定位精度不稳定。为此，开发了双动态自动定位技术，穿带过程中预留了足够的带钢打滑及下垂富余量，且带头与定位区中心线在助卷皮带咬入口静止状态下接触，消除了影响带头定位精度的主要因素，带头定位精度能稳定在±15 mm的误差范围内。实际应用效果表明，该方法可行、实用。     

THEORETICAL CALCULATION OF POINT DEFECTS IN Ni_3Al

Equilibrium equation of point defects in Ll_2 type intermetallic compounds was established tocalculate the relations of the concentration of antisite defects and vacancies and bulk composi-tion in Ni_3Al.The examination of temperature effects on the point defects cleared up the mis.understanding of the properties of the“constitutional point defects”in Ni_3Al.     

铸件缺陷修补方法

简述了铸件缺陷的谷种修补方法及工艺，指出液膜溶解扩散焊是一种比较先进的焊补方法。     

冷轧带钢板形缺陷表达式回归及数学模型

介绍了武钢冷轧厂１２５０ｍｍＨＣ轧机板形控制基本原理及冷轧带钢板形缺陷的板形分量表达式的回归处理和数学模型     

铜合金挤压材缩尾缺陷的控制办法

分析了铜合金制品缩尾缺陷的产生原因,并提出了相应的预防措施.有效减少缩尾缺陷,提高产品质量和经济效益.