β″－Al_2O_3陶瓷的强化和韧化

研究了稳定ＺｒＯ＿２和部份稳定ＺｒＯ＿２对β″－Ａｌ＿２Ｏ＿３陶瓷的强化和韧化作用，观察了不同种类、不同含量的ＺｒＯ＿２对β″－Ａｌ＿２Ｏ＿３陶瓷的显微结构、力学性能和电导率的影响，探讨了β″－Ａｌ＿２Ｏ＿３的韧化机理。     

WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

Corrosion fatigue short crack growth behaviour in a high strength steel

The influence of an aggressive environment (0.6 M, aerated NaCl solution) on short fatigue crack initiation and growth behaviour has been studied. The study involved three major test series, namely: air fatigue, corrosion fatigue, and intermittent air fatigue/corrosion fatigue. The above tests carried out under fully reversed torsional loading conditions at a frequency of 5 Hz, showed that it was the non-metallic inclusions which took part in crack initiation resulting from debonding at metal matrix/inclusion interface and pitting of inclusions in both air and corrosove environments, respectively. Short fatigue crack growth results in these two environments obtained by using plastic replication technique, indicated a large effect of microstructure i.e. prior austenite grain boundaries. The stage/stages at which the environmental contribution was dominant has been discussed by considering the results achieved from intermittent tests. However, the mechanisms involved in corrosion fatigue short crack growth have also been described in the light of results obtained from futher investigations carried out by conducting corrosion fatigue tests under applied cathodic potential conditions and tests on hydrogen pre-charged specimens under air fatigue and uniaxial tension conditions.     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

线性时变系统的区间稳定性与鲁棒稳定性

本文应用向量比较定理研究线性时变系统的区间稳定性和具非线性时变摄动的线性时变系统的鲁棒稳定性，所得的新结果包含文献的一些主要结果作为特例，本文的研究方法说明向量比较方法是分析区间稳定性和鲁棒稳定性的一种自然而有力的工具。     

β－C_2S固溶体稳定的热力学研究

从热力学理论出发，利用Ｘ射线衍射定性和定量的方法，对β－Ｃ＿２Ｓ固溶体的稳定性进行了分析和研究。经热力学理论推导得出β－Ｃ＿２Ｓ稳定的热力学条件，即掺入的微量元素的化学位μ＿ｉ须小于β－Ｃ＿２Ｓ的反应自由焓△Ｇ＿β，μ＿ｉ＜△Ｇ＿β．并定量地计算出一种微量元素稳定β－Ｃ＿２Ｓ的临界掺加量为；多种微量元素对β－Ｃ＿２Ｓ的稳定性判断条件为：     

LaCrMnNiO系热敏陶瓷的微观结构控制

通过对不同配方、工艺下的ＬａＣｒＭｎＮｉＯ系热敏陶瓷的微观结构研究，指出材料的相组成对其宏观电性能的影响，并提出了通过复合工艺利用“过渡相”的形成，对材料的“最终相”加以控制的方法。文中列出了使用ＸＲＤ及ＸＰＳ手段对材料微观结构的分析结果及有关电性能的测试数据。     

The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

微量Ag对CP276合金性能和组织的影响

研究添加不同含量的Ａｇ对ＣＰ２７６合金的拉伸性能和时效组织的影响。对拉伸强度、延伸率测试及透射电镜观察表明：０．１１ｗｔ％加入可促进Ｔ１相析出，使合金强度值升高；０．３５ｗｔ％Ａｇ的加入可在时效前期生成富Ａｇ、Ｍｇ的稳定的ＧＰ区，从而降低合金中Ｃｕ的固溶度，阻碍Ｔ１相析出，时效后期，ＧＰ区分解，生成大量Ｔ１相，使合金强度值显著升高。